Advertisement
Quick Links
1
500S™ SATELLITE GS AUTHORIZATION CODES
REQUIRED 500S™ FIRMWARE
The 500S™ GNSS receiver must have firmware version 5.9Aa06 or higher in order to use Satellite GS or GS-Lite. This
firmware version is included with CRx software 2.2 and above. Note that the CRx software update does not automatically
install the 500S™ firmware. Refer to
How to Update Hardware with CRx Devices
for instructions on this process.
GS VS. GS-LITE
Both Satellite GS and GS-Lite will require you to enter a 10-digit code into the 500S™ receiver. However, Satellite GS is a
subscription only and GS-Lite is a one-time unlock.
THE PROCESS
GATHER THE SERIAL NUMBER FOR THE 500S™
When ordering GS corrections for the 500S™, the receiver serial number is the only required piece of information. The
serial number for the 500S™ is located on the sticker on the bottom of the receiver. There will be 2 Raven product
stickers on the receiver: one is for the Raven serial number and the other is for the hardware serial number. You will need
the ESN (Electronic Serial Number) on the hardware serial number sticker.
Raven Serial Number
(Do Not Use)
Hardware Serial
Number
You may also find the 500S™ serial number using the screens for the CR7™ field computer and the SC1™ steering system.
CR7™ LOCATION
1.
Go to the Settings menu
and then navigate to GPS.
© 2019 Raven Industries, Inc.
Advertisement
Related Manuals for Raven 500S
Summary of Contents for Raven 500S
- Page 1 GS VS. GS-LITE Both Satellite GS and GS-Lite will require you to enter a 10-digit code into the 500S™ receiver. However, Satellite GS is a subscription only and GS-Lite is a one-time unlock. THE PROCESS GATHER THE SERIAL NUMBER FOR THE 500S™...
- Page 2 Go to the Information tab and then select the Information button next to the satellite map. SC1™ LOCATION 1.3.0.90 or higher SC1™ software is required for configuring the 500S™ through the SC1™. From the Home screen on the SC1™, select the Diagnostics softkey © 2019 Raven Industries, Inc.
-
Page 3: Entering Authorization Codes
NOTE ON SERIAL NUMBERS If the serial number for your 500S™ is 19423186 or lower, you will receive a 56-digit code in addition to the standard 10- digit code. The 56-digit code is a one-time-use code that will enable your 500S™ to use 10-digit codes in the future. - Page 4 10-digit code using the same process. If you did not receive a 56-digit code, you will only need to enter the 10-digit code. Remember to enter these codes exactly as they appear (case sensitive). After the 10-digit code is entered, the 500S™ will immediately be capable of receiving GS corrections. USING THE SC1™...
- Page 5 10-digit code. Remember to enter these codes exactly as they appear (case sensitive). The SC1™ will automatically detect if the 500S™ needs a 56-digit code. You will see the screen above when you need to enter a 56-digit code, and you will see the screen below when you need to enter a 10-digit code.
- Page 6 If subscribed to Satellite GS, the GPS Quality number should be 4. This may take up to 30 minutes. b. If unlocked for GS-Lite, the GPS Quality number should be 2. USING THE SC1™ Navigate back to the Tools menu and then go to the GPS Setup tab. Select Differential Configuration Setup. © 2019 Raven Industries, Inc.
- Page 7 Now go to GPS Information. If subscribed to Satellite GS, the GGA Quality (Mode) number should be 4. This may take up to 30 minutes. b. If unlocked for GS-Lite, the GGA Quality (Mode) number should be 2. © 2019 Raven Industries, Inc.