Subscribe to Our Youtube Channel
Summary of Contents for Ecovolt Zero1
- Page 1 Operation Instruction For the user and the qualified installer De-centralised MVHR Zero1 Manual www.ecovolt.ie ECO VOLT | ZERO1...
-
Page 2: Table Of Contents
MAIN TECHNICAL PARAMETERS DESIGN AND OPERATING LOGIC MOUNTING AND SET-UP CONNECTION TO POWER MAINS CONTROLS MAINTENANCE TROUBLESHOOTING STORAGE AND HANDLING Unit 3B Rosemount Park Drive, Info@ecovolt.ie +353 (0)1 5240387 Rosemount Business Park, www.ecovolt.ie Dublin 11, Ireland ECO VO LT | ZERO 1... -
Page 3: Safety Requirements
Keep the manual in a safe place for outside the future referencing temperature range stated in the user’s manual or in aggressive or explosive environments. The electrical connections must be completed by a competent and qualified person ECO VOLT | ZERO1... - Page 4 Do not use dam- Zero1 with water. aged equipment Protect the Zero1 or conductors to electric parts from connect the Zero1 to water ingress. power mains. Do not block the air While installing the duct when the Zero1 follow the Zero1 is on.
-
Page 5: Introduction
Operation Instruction For the user and the qualified installer INTRODUCTION This user’s manual included technical operation, installation and mounting guidelines for the de-centralised THE ZERO1 IS NOT INTENDED TO BE MVHR Zero1. USED BY CHILDREN OR PERSONS WITH PHYSICAL OR MENTAL DISABILITIES. ALL INSTALLATIONS... -
Page 6: Main Technical Parameters
80%. improved, so some models may slightly differ from those ones The Zero1 is classified as a class I elec- described in this manual. tric appliance. ZERO1 OVERALL DIMENSIONS (MM) 56.00 242.00 30.10 87.87 250.00-400.00... -
Page 7: Design And Operating Logic
The Zero1 generates an alarm sound when the filter requires cleaning or replacing The Zero1 uses the warm extracted air to heat up the ceramic core. The ceramic core is equipped with a pull cord to remove it from the inner sleeve, the ceramic core also acts as a sealant too. - Page 8 Operation Instruction For the user and the qualified installer Panel Noise Reduction EVA Buttons Top shell Chassis Mounting Plate Round Frame DC Brushless Motor Blade Inner Ducting Separated Frame Ceramic Heating Exchange Core Pre-Filter Separated Frame Outer Ducting Rubber Ring Air Louvre Cover ECO VOLT | ZERO1...
-
Page 9: Mounting And Set-Up
Cycle Mode: The unit works in supply and extract mode In cycle mode the Zero1 operates in two cycles for 65 seconds each. During cycle 1, the warm stale air is extracted from the room. As the air flows through... - Page 10 Operation Instruction For the user and the qualified installer MOUNTING 3. Mark the cable entry for the power cables and drill a hole in the mounting THE ZERO1 plate for the cables. Ensure the airtight- ness layer for the building is not com- promised at this point.
-
Page 11: Connection To Power Mains
N. Connect the earth conductor (PE) to the terminal marked E. The Zero1 MVHR is rated for 230VAC. 6. nstall the ventilation unit onto the mounting plate. The ventilation unit is fixed with magnets... - Page 12 Operation Instruction For the user and the qualified installer ZERO1 CONTROLS AND REMOTE CONTROL OPTIONS Electrical parameter Operating Voltage: DC3V(CR2025Button battery ) Emission current<5mA Sleep standby current<10µA Effective control distance: partition Walls>15m, open>30m Carrier frequency: RF 433.92MHz ON/OFF ON/OFF Press with...
-
Page 13: Maintenance
Operation Instruction For the user and the qualified installer OPERATING CONTROLS 4. Operation mode FROM THE ZERO1 UNIT Fresh Air mode. Air is supplied 1. Turning the Zero1 on. Adjusting the to the room at a set speed speed regardless of CN7 jumper. Press with... - Page 14 Remove the second filter after the core. Clean both filters and the ceramic core usin a hoo- ver and soft cloth. The Zero1 is equipped with an alarm sounder to alert the user that the filters require cleaning. This alarm can be reset once the cleaning maintenance has been carried out.
-
Page 15: Troubleshooting
ćremove the debris from blades are clogged the blades of the fan Automatic switch tripping Electrical fault inside Contact your local service following the Zero1 being the unit centre switched on Fan speed set to low Adjust the fan speed... -
Page 16: Storage And Handling
A full list of terms and conditions associated with the product’s war- ranty can be found on the manufacturer’s website. RETURNS If you have a faulty product, please return it to the address below. Ecovolt Limited, Unit 3B, Rosemount Park Drive, Rosemount Business Park, Ballycoolin Dublin 11, Ireland, D11 H029 Unit 3B Rosemount Park Drive, Info@ecovolt.ie...
Need help?
Do you have a question about the Zero1 and is the answer not in the manual?
Questions and answers