Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Michigan Welding PLASMA30
Summary of Contents for Michigan Welding PLASMA30
- Page 1 30A PLASMA CUTTER PART NO: PLASMA30 (..172844)
-
Page 2: Table Of Contents
DESCRIPTION ........................... 9 INSTALLATION ........................12 Operation ..........................13 Manual cutting ........................14 SERVICE, MAINTENANCE, TRANSPORTATION & STORAGE .......... 15 PLASMA30 TROUBLE SHOOTING CHART ................. 17 MAIN CIRCUIT CHART ......................19 PARTS BREAKDOWN ......................20 NOTES: ............................. 22 WARRANTY INFORMATION ....................24... -
Page 3: General Safety Rules
WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in serious injury. Do not allow persons to operate or assemble this PLASMA30 until ! CAUTION they have read this manual and have developed a thorough... - Page 4 • Keep hands and fingers away from moving parts and stay away from the drive rolls. • Do not point MIG gun at any body part of yourself or anyone else. • Always use this welder in the rated duty cycle to prevent excessive heat and failure. PLASMA30...
- Page 5 Specific Areas of Danger, Caution or Warning Electrical Shock • Electric arc machines can produce a shock that can cause injury or death. Touching electrically live parts can cause fatal shocks and severe burns. While cutting, all metal components connected to the wire are electrically hot.
- Page 6 • Keep work lead connected as close to the weld area as possible to prevent any unknown, unintended paths of electrical current from causing electrical shock and fire hazards. • To prevent any unintended arcs, cut wire back to ¼” stick out after welding. PLASMA30...
- Page 7 Hot Materials • Welded materials are hot and can cause severe burns if handled improperly. • Do not touch welded materials with bare hands. • Do not touch MIG gun nozzle after welding until it has had time to cool down. Sparks/Flying Debris •...
-
Page 8: Proper Care, Maintenance And Repair
Broken parts will affect the PLASMA30 operation. Replace or repair damaged or worn parts immediately. • When PLASMA30 is not in use, store it in a secure place out of the reach of children. Inspect it for good working condition prior to storage and before re-use. -
Page 9: Description
DESCRIPTION The PLASMA30 is an efficient method of cutting metal. Its working principle is to use compressed air as the ionization medium and forms a high-density plasma arc heat source by the torch nozzle's compression effect, which as a result melts the metal. The melted metal will be blown off by the high speed air flow and at the same time to forms a narrow cutting slot, thus the metal can be cut very rapidly. - Page 10 Unpacking Remove cartons, bags or Styrofoam containing the welder and accessories. Check the contents with the packing list below. Item PLASMA30 power source 1 unit 5M PT31 Plasma torch 3M Earth Clamp Guide wheel Hose Clamp Regulator w/nitto coupler Wrench...
- Page 11 Cut Current Setting Knob Adjusts the cut amperage Power Indicator: When the machine is turned on, the power indicator will be on. Working Indictor: When the cutting torch be triggered, the working indictor will be on Alarm Indicator: When the thermal indicator is on, it shows the machine is overloaded and the internal temperature is too high.
-
Page 12: Installation
Replace the nozzle when it becomes ineffective and effects cutting performance. The electrode should be replaced when it is shortened to about 2mm Ensure cables and pipes are not damage or excessively worn Cutting Torch Assemble Sketch PLASMA30... -
Page 13: Operation
Appearance and Connection Operation Switch on the power supply switch at rear of the machine. Check the front panel to ensure none of the warning lights are 'on'. If it is normal you should hear the fan run; and the (Power Indicator) should be on. Adjust air regulator valve to required pressure to suit cutting thickness. -
Page 14: Manual Cutting
Material Steel plate Cutting Air Flow thickness Current (A) L/min Steel 2-5mm 15 - 20 20 - 28 Steel 6-8mm Steel 10mm 28-30 15 - 20 2-4mm Stainless Steel 4-6mm 20 - 30 Stainless Steel PLASMA30... -
Page 15: Service, Maintenance, Transportation & Storage
Maintenance and Service • The PLASMA30 welder is a semi-automatic gas shielded welder. To properly operate & maintain the welder can assure it of good performance and prolong its operating life. - Page 16 • Switch off the power source each time when removing dust. No touching inside cable or work piece while removing dust. While practicing to use your new welder, experiment holding the torch in different positions until you find the one that seems to work best for you. PLASMA30...
-
Page 17: Plasma30 Trouble Shooting Chart
PLASMA30 TROUBLE SHOOTING CHART No Breakdown Analysis Solutions Voltage is too high (≥15%) Switch off power source; Check the main supply; Voltage is too low (≤15%) Restart welder when power recovers to normal state. Circumstance temperature It will automatically recover Alarm is too high. - Page 18 Please connect with our company Others PLASMA30...
-
Page 19: Main Circuit Chart
MAIN CIRCUIT CHART OPERATING MANUAL... -
Page 20: Parts Breakdown
PARTS BREAKDOWN PLASMA30... - Page 21 Materiel NO. Part Name Code Top Cover S2043552 Handle 20300439 Handle Cover 20300441 Pneumatic Connector 12700095 Pressure Relief Valve 70100894 Power Cable 12700925 Cable Clip 30406017 Switch 30715118 Front Plastic 30203265 Fan Cover 30401010 30712234 Inductance 30605443 Bottom Case S2043553 Quick Connector VS020619 Insulation Base...
-
Page 22: Notes
NOTES: PLASMA30... - Page 23 NOTES: OPERATING MANUAL...
-
Page 24: Warranty Information
MULTI80S2 POWER SOURCE Warranty Period Original main Transformer 1 Year Original main power rectifiers, printed circuit boards and power 2 Year switch semiconductors PLASMA30 ACCESSORIES Warranty Period Electrode holder, earth clamp and cables 3 months March 17, 2021 8:59 am...
Need help?
Do you have a question about the PLASMA30 and is the answer not in the manual?
Questions and answers