Summary of Contents for HARTING mCon 3000
- Page 1 HARTING Ha-VIS Management Software mCon 3000 Next Generation User Manual Web Interface...
- Page 2 No part of this manual may be reproduced in any form (print, photocopy, microfilm or any other process), processed, duplicated or distributed by means of electronic systems without the written permission of HARTING Electric GmbH & Co. KG, Espelkamp. Subject to alterations without notice.
-
Page 3: Table Of Contents
Content Introduction ................................ 7 Safety Guidelines and Approved Usage ......................8 General Notes about this Manual ........................9 Explanation of the symbols ..........................9 Typographical conventions..........................9 Additional information............................9 Basic Operation ..............................10 Switch access and configuration ........................10 Web access ............................... - Page 4 IP Authorized Manager ..........................54 Index .................................. 98 Figure 13-2 802.1x Basic Settings tab ......................... 55 Figure 13-3 Port Settings tab ............................56 Figure 13-4 Local Server tab ............................57 HARTING Electric GmbH Management Software Ha-VIS mCon Series / Edition 2.4...
- Page 5 Assign Device Name ..........................88 Figure 20-7 Select the switch and assign the names ....................89 Figure 20-8 Slots and modules of the Ha-VIS mCon 3000 Next Generation switches ..........89 Figure 20-9 Alarms on Slot 0 ............................90 Figure 20-10 Topology settings ............................
-
Page 6: Introduction
This information is applicable for all switches in the Ha-VIS mCon 3000 NG series. The examples and screenshots in this manual are taken from the Ha-VIS mCon 3102-AASFP; the number of ports and the information shown in your software may vary depending on the model of switch you use. -
Page 7: Safety Guidelines And Approved Usage
3.1 Explanation of the symbols appropriately operated. The switch management software should be used only in conjunction with a HARTING Ethernet switch. The following symbols are used in this software guide: Observe the following general safety instructions before installing and using the switch... -
Page 8: Basic Operation
The Login Screen is then once again displayed. you have to copy the HARTING MIB file to your MIB repository of your SNMP software. The third way of configuring the switches is to use the command line interface (CLI). The CLI 4.3 SNMP configuration... -
Page 9: Multifunction Button
Reset to factory defaults, Set the switch to factory default settings with the exception of the IP correctly. keep IP address HARTING Electric GmbH Management Software Ha-VIS mCon Series / Edition 2.4... -
Page 10: Accept And Saving Changes With The Save Configuration Button
Figure 6-3 Save Configuration button HARTING Electric GmbH Management Software Ha-VIS mCon Series / Edition 2.4... -
Page 11: User Rights
Figure 7-1 The Overview section Function Description Device Name Displays the type of HARTING Ethernet switch in use. Default value: Ha-VIS mCon 3080-A, Ha-VIS mCon 3102-AASFP Device Contact Displays contact information, as defined by the user in the General Settings section. -
Page 12: System Settings
Note The IP address assigned to the switch must be unique for the respective network! Connectivity problems will arise if two network components are assigned the same IP address. HARTING Electric GmbH Management Software Ha-VIS mCon Series / Edition 2.4... -
Page 13: Port Settings
Link Status Displays the port status. A green circle in this column indicates that a device is connected to this port. A red circle indicates that no device is connected. HARTING Electric GmbH Management Software Ha-VIS mCon Series / Edition 2.4... -
Page 14: User Management
For the usage of the Ha-VIS mCon 3102-AASFP the following restrictions apply: Depending on the capabilities of the used SFP-modules the adjustable parameters may vary. For example, it is not possible to deactivate Autonegotiation and Autocrossing for Gigabit SFP-Modules. HARTING Electric GmbH Management Software Ha-VIS mCon Series / Edition 2.4... -
Page 15: Snmp
Multifunction Button. To learn how to use the Multifunction Button refer to Chapter 5 – „Multifunction Button“. Figure 8-7 SNMP section HARTING Electric GmbH Management Software Ha-VIS mCon Series / Edition 2.4... - Page 16 If you don’t plan to use SNMP, you should make sure that both versions are disabled so that maximum security is ensured. The HARTING SNMP Agent provides complete support for User based Security Model. The following security algorithms are supported: Note A MIB (Management Information Base) file can be found on the enclosed CD.
-
Page 17: Network Discovery
• Neighbour Chassis ID Chassis ID of the neighbour device • Neighbour Port ID Port ID of the neighbour device • Neighbour IP IP address of the neighbour device HARTING Electric GmbH Management Software Ha-VIS mCon Series / Edition 2.4... -
Page 18: Time Settings
The Simple Network Time Protocol is a subset of the Network Time Protocol used to synchronize specified PC in the network that serves as a time generator. The IP computer clocks in the Internet. HARTING switches implement the client portion of the SNTP protocol address must be specified. More than one server may be specified and do not implement the server portion. -
Page 19: Vlan
User Manual Ha-VIS mCon Switch Management Software System Settings HARTING Ha-VIS mCon 3000 switches can be operated in the following PTP modes: 8.7 DHCP Relay Agent • Boundary Clock: The device can either be a master or a slave. As a slave, the switch Upgrading and changing the structure of Ethernet networks usually causes a lot of administrative synchronizes the clock with another master. - Page 20 ATTENTION Only select firmware files that are compatible with the device for the import functionality. Figure 8-14 Import/Export Firmware tab HARTING Electric GmbH Management Software Ha-VIS mCon Series / Edition 2.4...