WAM WATERMIZER 3335 Owner's Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

WATERMIZER

OWNER'S MANUAL

Revised 08.21

308.708.8185 | Info@WAMfgco.com | Manual Part Number - 123016 | Rev. 08/21

Table of Contents

Summary of Contents for WAM WATERMIZER 3335

Page 1 WATERMIZER OWNER’S MANUAL Revised 08.21 308.708.8185 | Info@WAMfgco.com | Manual Part Number - 123016 | Rev. 08/21...
Page 2 This manual is applicable to: Watermizer Record the model number and serial number of your Watermizer along with date purchased: MODEL NUMBER SERIAL NUMBER DATE PURCHASED SERIAL NUMBER The serial number plate is located on the frame to be readily available. It is suggested that your serial number and purchase date also be recorded above.
Page 3: Pre-Delivery Checklist
TO THE DEALER Factory to Farm™ service includes full factory assembly. Dealer is responsible for field readiness. PRE-DELIVERY CHECKLIST Use the following checklist after your Watermizer is completely assembled. Check off each item as it is found satisfactory or after proper adjustment is made. All working parts move freely, bolts are tight, and cotter pins are spread.
Page 4: Delivery Checklist
DELIVERY CHECKLIST Use the following checklist after your Watermizer is delivered as a reminder of very important information which should be conveyed to retail customer/end user. Check off each item as it is fully explained. Life expectancy of this or any other machine is dependent on regular lubrication as directed in the Owner’ s Manual. All applicable safety precautions.
Page 5 OWNER’S MANUAL INDEX GENERAL INFORMATION HOW TO USE THIS MANUAL 1 WARRANTY INFORMATION 2 SAFETY...
Page 7: General Information
GENERAL INFORMATION HOW TO USE THIS MANUAL This manual is divided into sections. The first section contains a Table of Contents, General Information, and a Part Number Index. The remaining sections divide the machine into assemblies and sub-assemblies which illustrate and list all parts. W&A Manufacturing parts in this manual are specially designed for this machine and should be replaced with W&A Manufacturing parts only.
Page 8: Warranty Information
GENERAL INFORMATION INTRODUCTION Thank you for your purchase of a W&A Manufacturing Watermizer. Putting your trust in our equipment is something we don’t take lightly and are humbled that you chose W&A Manufacturing. Having designed all of our equipment with farmers like you in mind, we hope you enjoy years of productive use from it.
Page 9: Signal Words
SAFETY SAFETY TAKE NOTE! THIS SAFETY ALERT SYMBOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL YOUR ATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONAL SAFETY AND THE SAFETY OF OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH. THIS SYMBOL MEANS: -ATTENTION! -BECOME ALERT!
Page 10: Equipment Safety Guidelines
SAFETY SAFETY... YOU CAN LIVE WITH IT! EQUIPMENT SAFETY GUIDELINES Safety of the operator is one of the main concerns in designing and developing a new piece of equipment. Designers and manufacturers build in as many safety features as possible. However, every year many accidents occur which could have been avoided by a few seconds of thought and a more careful approach to handling equipment.
Page 12: Safety Sign Locations
SAFETY SAFETY SIGN LOCATIONS These types of Safety Signs and locations on the equipment are shown in the illustrations below. Good safety requires that you familiarize yourself with the various Safety Signs, the type of warning and the area, or particular function related to that area, that require your SAFETY AWARENESS.
Page 13 SAFETY 461213 PINCH POINT - WARNING • Keep extremities clear of equipment. Object(s) can move or shift; can result in death or serious injury. • Hazards may include, but are not limited to, hinge mechanism movement, pin movement, row unit movement and shifting, accessory movement and shifting, etc. 461220 CRUSH HAZARD - WARNING •...
Page 14: No Riders - Warning
SAFETY 461225 CRUSH HAZARD - WARNING • Keep clear of moving and shifting equipment. Equipment can move or shift; can result in death or serious injury. • Hazards may include, but are not limited to, folding wing movement, raised equipment movement and shifting, etc.
Page 15 SAFETY 461248 CONTENTS UNDER PRESSURE - WARNING • Do not operate if damaged or improperly pressurized. Damaged or improperly pressurized components can discharge; can result in death or serious injury. • Hazards may include, but are not limited to, damaged tire and/or rim, over pressurized tire, excessive tire wear, tire tears or punctures, ect.
Page 16 SAFETY 461255 ELECTRICAL SHOCK/ELECTROCUTION HIGH-CLEARANCE DANGER • Keep clear of overhead power lines, maintain 20-foot minimum distance. Electrical shock and/or electrocution can occur; will result in death or serious injury. • Hazards may include, but are not limited to, high clearance equipment, low clearance power lines, lack of awareness of surroundings, etc.
Page 17: Safety Sign Care
SAFETY SAFETY SIGN CARE • Keep safety signs clean and legible at all times. • Replace safety signs that are missing or have become illegible. • Replaced parts that displayed a safety sign should also display the current sign. • Safety signs are available from W&A Manufacturing.
Page 19: Preparation And Setup
PREPARATION & SET-UP This section helps you prepare your tractor and Watermizer for use. You must level the implement, hook up the implement hydraulics to the tractor, and check that the hydraulics have been bled. POST-DELIVERY/SEASONAL SET-UP On initial delivery, use with a new tractor, and seasonally check and as necessary, complete these items before continuing to the routine set-up items: Bleed hydraulic fold system (page 48) Check/Change Hitch Configuration...
Page 20 PREPARATION & SET-UP CHECK/CHANGE HITCH CONFIGURATION On initial delivery, use with a new tractor, and seasonally check and as necessary, complete these items before continuing to the routine set-up items: Choose a hitch option that is compatible with your tractor 3-point. The Watermizer has two hitch configurations: •...
Page 21 PREPARATION & SET-UP TO OPERATE AS CATEGORY 4N 1 Remove top and lower Category 3 pins shown and store them. 2 Once removed, the remaining pins are set to run the implement with a Category 4N hitch. MAIN INDEX PARTS INDEX 308.708.8185 | Info@WAMfgco.com | Rev.
Page 22 PREPARATION & SET-UP HITCHING TRACTOR TO IMPLEMENT On initial delivery, use with a new tractor, and seasonally check and as necessary, complete these items before continuing to the routine set-up items: 1 Connect the tractor 3-point lift arms to the lower hitch pins.
Page 23: Hydraulic Hose Hook-Up
PREPARATION & SET-UP HYDRAULIC HOSE HOOK-UP Folding Watermizers are equipped with independently controlled fold cylinders to individually fold the left and right wings. This section does not apply to Rigid toolbar models. This requires the use of two remote valves. Hoses at base end of cylinder will unfold machine. Rod end hoses will fold machine up.
Page 24: Folding Toolbar
PREPARATION & SET-UP LIGHT KIT GUIDE AND RELOCATION The light kit is installed at the factory. However, due to shipping requirements and other circumstances, some positions are altered and SMV sign or lights may need relocated before use. Typically, the SMV sign is the only component that needs relocated;...
Page 25: Electrical Hook-Up
PREPARATION & SET-UP ELECTRICAL HOOK-UP Lights are connected using a standard 7-pin connector. To connect, simply lift receptacle cover, align plug and insert. To disconnect, lift receptacle cover and remove plug. Once connected, check to make sure all lights are working properly.
Page 26 PREPARATION & SET-UP LEVELING THE IMPLEMENT - RIGID & FOLDING Figure 1 Center Frame L/R Leveling - RIGID & FOLDING (Figure 1) LEVEL 1 Hitch the Watermizer to a tractor (page 12-15). 2 Raise the implement. 3 Adjust the tractor 2-point lift arms so that the center section tool bar is level.
Page 27 PREPARATION & SET-UP GAUGE WHEEL TIRE INFLATION Gauge wheels inflated to the proper air pressure is an important factor in getting the best performance out of your Watermizer while increasing the longevity of the life of your gauge wheels. Underinflation can damage the tire and decrease the life expectancy of your gauge wheel. Initial tire pressure should be set at 30 PSI for your Watermizer gauge wheels.
Page 29: Before Operation
OPERATION REMEMBER Your best assurance against accidents is a careful and responsible operator. If there is any portion of this manual or function you do not understand, contact W&A Manufacturing. BEFORE OPERATION • Carefully study and understand this manual. • Do not wear loose-fitting clothing which may catch in moving parts.
Page 30: Pre-Start Checklist
OPERATION This section covers general operating procedures. Experience, machine familiarity, and the following information will lead to efficient operation and good working habits. Always operate farm machinery with safety in mind. PRE-START CHECKLIST Perform the following steps before transporting the Watermizer to the field. Carefully read “Important Safety Information”...
Page 31 OPERATION FOLDING & UNFOLDING - FOLDING TOOLBAR Fold the implement for movements on public roads and between fields and narrow clearances. Do not use the folded configuration for parking or storage. 1. Hitch to tractor (page 14). 2. Move to level ground. Be aware of vertical clearance needed to fold implement. 3.
Page 32 OPERATION TRANSPORT CHECKLIST Before transporting the implement, check the following items. Transport only with a tractor of proper size and adequate ballast. Hitch implement securely to tractor. See “Hitching Tractor to Implement” on page Plug implement safety lights into tractor seven-pin connector on page Make sure implement is folded properly.
Page 33: Gauge Wheel Adjustment
OPERATION GAUGE WHEEL ADJUSTMENT Gauge wheels are equipped with two different methods to adjust the depth of the gauge wheels. The first is to use the ratchet jack. To do this, loosen the jam nut with a combination wrench ( 1 ¾”). Then, turn the ratchet jack to either lengthen or shorten the ratchet jack.
Page 34: Leveling The Machine
OPERATION LEVELING THE MACHINE When initially setting the Watermizer up to operate in the field the machine should be set level front to back and level left to right. To level center and wings refer to “Leveling the Implement” section on page 18. In order to set front to back level of machine, pull into field, then lower implement in ground.
Page 35: Depth Settings
OPERATION DEPTH SETTINGS BASIC DEPTH SETTINGS FOR USE IN FIELDS WITH EXISTING RAISED BEDS -Park the machine on a level surface. -Use the tractor to level the implement front to rear (see page 25). GAUGE WHEELS RATCHET As a recommend starting point, adjust the gauge JACK wheels so the measurement from the top bolt of the ratchet jack to the bottom bolt of the ratchet...
Page 36 OPERATION DEPTH ADJUSTMENT - WATERMIZER To set the depth of the Irrigation Sweeps: 1. Locate the shank adjustmen set bolts on the shank holder and loosen the jam nuts and shank adjustmen set bolts to allow the shank to move in the shank holder 2.
Page 37 OPERATION ANGLE ADJUSTMENT - WATERMIZER To set the angle of the Irrigation Sweeps: 1. Using a pair of 3/4” wrenches, loosen the foot piece pivot bolt and the adjustment bolt. 2. Move the sweep to the desired angle, then tighten adjustment and pivot bolts. MINIMUM ANGLE (FLAT) PIVOT BOLT...
Page 38: Speed Recommendations
OPERATION SPEED RECOMMENDATIONS The ideal operating speed for the Watermizer is 4-6 mph. Field conditions can change the effectiveness of the Watermizer and need to be taken into consideration by the operator. • Ideal operating speed: 4-6 mph • Minimum operating speed: 4 mph •...
Page 39 OPERATION PARKING For long-term parking, see also “Storage” below. 1. Choose a parking location that has room for unfolding, is level, has firm soil and is unlikely to develop soft soil in rain. With the implement still hitched, maneuver it to the parking location. If the implement must be parked folded, leave it hitched to the tractor.
Page 40: Following Operation
OPERATION FOLLOWING OPERATION • Store the unit in an area away from human activity. • Do not park equipment where it will be exposed to livestock for long periods of time. Damage and livestock injury could result. • Do not permit children to play on or around the stored unit. •...
Page 41 OPERATION WATERMIZER DO’S AND DON’TS • DO follow all safety precautions in this manual. • DO locate and familiarize yourself with the various Safety Signs and instructional decals prior to operation. • DO inspect equipment for damage and wear before use; repair as needed. •...
Page 43: Troubleshooting
TROUBLESHOOTING Troubleshooting Problem Possible Cause Solution Shank depth is too shallow. Adjust shanks and gauge wheels down. Toolbar contacts the crop. Crop is too tall for correct use of the Use the machine before the crop is too tall. implement. Adjust machine, or tractor hitch, to be level side to side.
Page 45 MAINTENANCE & LUBE MAINTENANCE • Proper maintenance will ensure longevity and optimum performance of your W&A equipment. • Visual inspection is recommended before each use. Check for loose bolts, worn parts, cracked welds and other damage. Replace and repair as needed. •...
Page 46 MAINTENANCE & LUBE DAILY MAINTENANCE 1. Inspect machine for any loose or missing hardware. 2. Inspect hydraulic lines and connections for wear, bulging hoses, or leakage. WEEKLY MAINTENANCE 1. Grease the toolbar hinges - five (5) for a Single 7x7 hinge. (Grease zerks indicated in yellow circles below.) Toolbar Hinge Single 7x7...
Page 47: Bleeding Fold Hydraulics
MAINTENANCE & LUBE BLEEDING FOLD HYDRAULICS To function properly, the hydraulics must be free of air. If hydraulics have not been bled, they will operate with jerky, uneven motions and could cause wings to drop rapidly during folding or unfolding. If hydraulics were not bled during initial implement setup or if you replace a part in the hydraulic system during the life of the implement, complete the following procedures: Check hydraulic fluid level in tractor reservoir and fill to proper level.
Page 48: Checking Bolt Torque
MAINTENANCE & LUBE CHECKING BOLT TORQUE The table shown below gives correct torque values for various bolts and capscrews. Tighten all bolts to the torques specified in chart unless otherwise noted. Check tightness of bolts periodically, using bolt torque chart as a guide. Replace hardware with the same grade bolt. BOLT TORQUE CHART Torque Specifications Bolt Diameter...
Page 49 MAINTENANCE & LUBE HYDRAULIC FITTING IDENTIFICATION Hydraulic fitting styles, types and sizes are numerous and at times easily confused. The chart below shows the most common types and sizes of hydraulic fittings for the industry, male ends depicted. This chart is printed at 1 to 1 for ease of identification. NPTF (National Pipe Taper Fuel) uses tapered threads to create a seal.
Page 50 MAINTENANCE & LUBE CHECKING HYDRAULIC FITTINGS • Before connecting hydraulic fittings, check that fittings are clean and undamaged. Replacement fittings and hoses are available from W&A Manufacturing. • Ensure O-ring(s) are installed properly as shown in the image. (ORB fitting above, ORFS fitting below) •...
Page 52: Parts Guide
PARTS GUIDE PARTS GUIDE This Parts Guide applies to: Serial Number: Starting with L or newer (Level Banders manufactured between June 2020-June 2021). Starting June 2021, Serial Numbers will change to a 9-digit number (ex. 26XXXXX0721). For parts for models prior to serial numbers beginning with L (K or older), or manufactured before July 2020, please refer to the Legacy section of manuals under Level Bander on the Support page at WAMFGCO.com.
Page 53 PARTS GUIDE HOW TO USE THIS PARTS GUIDE 1. Determine your Watermizer Model by referring to the Model No. on your Serial Number plate on the hitch of your Watermizer. 2. Using your Model Number (eg. 3335 for a 8 Row 36”...
Page 54 PARTS GUIDE Parts Guide Model Number Index 3335 - 8 ROW 36 FOLDING 43 3330 - 8 ROW 38/40 FOLDING 44 3331 - 8 ROW 60 FOLDING...
Page 55 PARTS GUIDE REFERENCE MODEL 3335 - 8 ROW 36” FOLDING LIGHT KITS TOOLBAR Section Page Section Page Whole Hitch & Pins Toolbar Sub Assemblies GAUGE WHEELS Bar Stands Hydraulics Section Page Whole ROW ASSEMBLY Section Page Irrigation Sweep & Torpedo MAIN INDEX PARTS INDEX 308.708.8185 | Info@WAMfgco.com | Rev.
Page 56 PARTS GUIDE REFERENCE MODEL 3330 - 8 ROW 38”/40” FOLDING LIGHT KITS TOOLBAR Section Page Section Page Whole Hitch & Pins Toolbar Sub Assemblies GAUGE WHEELS Bar Stands Hydraulics Section Page Whole ROW ASSEMBLY Section Page Irrigation Sweep & Torpedo MAIN INDEX PARTS INDEX 308.708.8185 | Info@WAMfgco.com | Rev.
Page 57 PARTS GUIDE REFERENCE MODEL 3331 - 8 ROW 60” FOLDING LIGHT KITS TOOLBAR Section Page Section Page Whole Hitch & Pins Toolbar Sub Assemblies GAUGE WHEELS Bar Stands Hydraulics Section Page Whole ROW ASSEMBLY Section Page Irrigation Sweep & Torpedo MAIN INDEX PARTS INDEX 308.708.8185 | Info@WAMfgco.com | Rev.
Page 58 PARTS GUIDE REFERENCE MODEL 3332 - 12 ROW 30” FOLDING LIGHT KITS TOOLBAR Section Page Section Page Whole Hitch & Pins Toolbar Sub Assemblies GAUGE WHEELS Bar Stands Hydraulics Section Page Whole ROW ASSEMBLY Section Page Irrigation Sweep & Torpedo MAIN INDEX PARTS INDEX 308.708.8185 | Info@WAMfgco.com | Rev.
Page 59 PARTS GUIDE REFERENCE MODEL 3333 - 12 ROW 36”/38”/40” FOLDING LIGHT KITS TOOLBAR Section Page Section Page Whole Hitch & Pins Toolbar Sub Assemblies GAUGE WHEELS Bar Stands Hydraulics Section Page Whole ROW ASSEMBLY Section Page Irrigation Sweep & Torpedo MAIN INDEX PARTS INDEX 308.708.8185 | Info@WAMfgco.com | Rev.
Page 60 PARTS GUIDE REFERENCE MODEL 3334 - 16 ROW 30” FOLDING LIGHT KITS TOOLBAR Section Page Section Page Whole Hitch & Pins Toolbar Sub Assemblies GAUGE WHEELS Bar Stands Hydraulics Section Page Whole ROW ASSEMBLY Section Page Irrigation Sweep & Torpedo MAIN INDEX PARTS INDEX 308.708.8185 | Info@WAMfgco.com | Rev.
Page 61 PARTS GUIDE TOOLBAR - LARGE SINGLE BAR CENTER SECTION Item Number Part # Description Quantity 315806 LARGE SINGLE BAR CENTER SECTION 315802 SINGLE BAR 4R30 WIN 315613 FOLD LINK CENTER PLATE 315620 FOLDING CYLINDER LINK 315622 SHORT PIN 315624 LONG PIN 315627 MEDIUM PIN 315630...
Page 62 PARTS GUIDE TOOLBAR - LARGE SINGLE BAR CENTER SECTION Item Number Part # Description Quantity 476023 4 1/2 X 20 TIE ROD HYDRAULIC CYLINDER 315647 CYLINDER STOP 306284 WING LOCK PIN 315162 WIRE LOCKING PIN 1/4 X 1 3/8 USAEABLE LENGTH 411543 1/2-13 X 1 BOLT GR5 413007...
Page 63 PARTS GUIDE TOOLBAR - SMALL SINGLE BAR CENTER SECTION Item Number Part # Description Quantity 315807 SMALL SINGLE BAR CENTER SECTION 315804 SINGLE BAR 3R30 WING 315613 FOLD LINK CENTER PLATE 315620 FOLDING CYLINDER LINK 315622 SHORT PIN 315624 LONG PIN 315627 MEDIUM PIN 315630...
Page 64 PARTS GUIDE TOOLBAR - SMALL SINGLE BAR CENTER SECTION Item Number Part # Description Quantity 476023 4 1/2 X 20 TIE ROD HYDRAULIC CYLINDER 315647 CYLINDER STOP 306284 WING LOCK PIN 315162 WIRE LOCKING PIN 1/4 X 1 3/8 USAEABLE LENGTH 411543 1/2-13 X 1 BOLT GR5 413007...
Page 65 PARTS GUIDE HITCH & PINS Item Number Part # Description Quantity 315072 BOLT-ON HITCH CAT 3, 4N 315637 TIE-IN 315640 TIE-IN CLAMP 315150 HITCH PIN PACK 3, 3N & 4N 315151 TOP PIN CAT 4N 315152 TOP PIN CAT 3 315153 LOWER PIN CAT 4N 315154...
Page 66 PARTS GUIDE HITCH & PINS Item Number Part # Description Quantity 315157 EXTERNAL RETAINING RING FOR 2" SHAFT 315158 EXTERNAL RETAINING RING FOR 1 7/16" SHAFT 315161 WIRE LOCKING PIN 1/4 X 2 1/8 USEABLE LENGTH 315162 WIRE LOCKING PIN 1/4 X 1 3/8 USEABLE LENGTH 602012 CLAMP ASSEMBLY FOR 7 X 7 TO 5 X 7 TUBE 302014...
Page 67 PARTS GUIDE TOOLBAR - FOLDING HYDRAULICS Item Number Part # Description Quantity 476023 4 1/2 X 20 TIE ROD HYDRAULIC CYLINDER 306190 120" HOSE ASSEMBLY 306191 148" HOSE ASSEMBLY 457240 1/2" MALE AGTIP Q. COUPLER -8FORB STRAIGHT RESTRICTION 3/64" ORIFICE 8MORB X 8FORB SOLID 90° ELBOW 457241 FITTING 457261...
Page 68 PARTS GUIDE BAR STAND Item Number Part # Description Quantity 302222 BAR STAND MOUNT FOR 7X7 315203 BAR STAND LONG LEG 416230 SNAP LOCK PIN 3/4 X 4 EFFECTIVE LENGTH 415004 U-BOLT 3/4-10 7W X 9H TL-2" GR5 413512 3/4 LOCK WASHER 412012 3/4-10 HEX NUT GR2 MAIN INDEX...
Page 69 PARTS GUIDE FURROW PLOW AND TORPEDO ASSEMBLY Item Number Part # Description Quantity 728116 SHANK HOLDER ASSEMBLY FOR 7" SQUARE TUBING 479069 SHANK HOLDER FOR 7" SQUARE TUBING 204274 BACKING PLATE FOR 7" SQUARE TUBING 204603 36" SHANK 302265 TRIP FOOT 474047 7"...
Page 70 PARTS GUIDE FURROW PLOW AND TORPEDO ASSEMBLY Item Number Part # Description Quantity 302500 TORPEDO W/WELDED CHAIN HOOKS 400024 5/16 QUICK LINK 411837 7/16-14 X 3 1/2 PLOW BOLT GR5 410007 7/16-14 CENTER LOCK NUT 411549 1/2-13 X 2 1/2 BOLT GR5 413508 1/2 LOCK WASHER 412058...
Page 71 PARTS GUIDE LIGHT KIT - RIGID & FOLDING TOOLBAR Item Number Part # Description Quantity 302873 LIGHT KIT FOR SINGLE FOLDING TOOLBAR (MEDIUM) 302851 SMV SIGN & STRAIGHT BRACKET ASSEMBLY 204845 SMV SIGN STRAIGHT BRACKET 204836 SMV SIGN WITH GLAVANIZED BACKING **CONTINUED ON NEXT PAGE** MAIN INDEX PARTS INDEX...
Page 72 PARTS GUIDE LIGHT KIT - RIGID & FOLDING TOOLBAR Item Number Part # Description Quantity 302872 LH REAR FLAG BRACKET ASSEMBLY 204842 LH FLAG BRACKET 302871 RH REAR FLAG BRACKET ASSEMBLY 204843 RH FLAG BRACKET 204844 FLAG BRACKET STRAP 302877 LH FRONT MEDIUM FOLDING BAR BRACKET ASSEMBLY 302878 LH FRONT MEDIUM FOLDING BAR BRACKET...
Page 73: Gauge Wheels
PARTS GUIDE GAUGE WHEELS Item Number Part # Description Quantity 250001 GAUGE WHEEL MAIN BODY 250002 GAUGE WHEEL REAR CLAMP ZNF40506 GAUGE WHEEL REAR CLAMP NARROW (NOT SHOWN) 411586 3/4-10 X 2 1/2 GR5 Z/C 413512 3/4 LOCK WASHER **CONTINUED ON NEXT PAGE** MAIN INDEX PARTS INDEX 308.708.8185 | Info@WAMfgco.com | Rev.
Page 74 PARTS GUIDE GAUGE WHEELS Item Number Part # Description Quantity 410012 3/4-10 NUT CENTER LOCK Z/C 411650 1-8 X 8 GR5 Z/C 410016 1-8 NUT CENTER LOCK Z/C 411600 3/4-10 X 8 GR5 Z/C 305101 3/4-10 NUT NYLON LOCK Z/C 411592 3/4-10 X 4 1/2 GR5 Z/C 413072...
Page 75 870.5347420 | WAMFGCO.com PO BOX 5238, Pine Bluff, AR 71611 MAIN INDEX PARTS INDEX 308.708.8185 | Info@WAMfgco.com | Rev. 08/21...

This manual is also suitable for:

Watermizer 3330 Watermizer 3331 Watermizer 3332 Watermizer 3333 Watermizer 3334