Fantom PT301H Owner's Manual

Spin saw / rotary tool kit

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Owner's Manual

SPIN SAW / ROTARY TOOL KIT

Model No.

PT301H

WARNING

Always have one hand

firmly placed on the

tool body while

operating. Never

operate the tool by

holding only the tool

handle.

CAUTION:

Before using this Spin

Saw/Rotary Tool, read this

manual and follow all its

Safety Rules and

Operating Instructions.

FANTOM, 178 West Service Road, Champlain, N.Y. 12919

· Safety Instructions

· Accessories

· Assembly

· Operation

· Maintenance

Table of Contents

Need help?

Do you have a question about the PT301H and is the answer not in the manual?

Questions and answers

Summary of Contents for Fantom PT301H

Page 1: Safety Instructions
Owner’s Manual SPIN SAW / ROTARY TOOL KIT Model No. PT301H WARNING Always have one hand firmly placed on the tool body while operating. Never operate the tool by holding only the tool handle. CAUTION: Before using this Spin Saw/Rotary Tool, read this...
Page 2: Table Of Contents
To avoid electrical hazards, fire hazards or damage to the spin saw, use proper circuit protection. This spin saw is wired at the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere time delay fuse or curcuit breaker. To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way.
Page 3: Power Tool Safety
POWER TOOL SAFETY GENERAL SAFETY RULES WARNING Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. WORK AREA Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
Page 4: Spin Saw/ Rotary Tool Safety
SAVE THESE INSTRUCTIONS FOR REFERENCE SPIN SAW SAFETY Always wear safety goggles and dust mask. Use only in well ventilated area. Using personal safety devices and working in a safe environment reduces risk of injury. ALWAYS WEAR EYE PROTECTION. Any power tool lenses.
Page 5: Electrical Requirements & Safety
ELECTRICAL REQUIREMENTS & SAFETY DOUBLE INSULATION This cutting tool is double insulated to protect you from electrical shock. WARNING Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug.
Page 6 WARNING If any part is missing or damaged, do not plug the spin saw into the power source until the missing or damaged part is replaced and assembly is complete. Carefully unpack the spin saw and all its parts. Compare against the “Spin Saw Components”...
Page 7: Carton Contents
CARTON CONTENTS SPIN SAW COMPONENTS DESCRIPTION Spin Saw Precision Handle with Sole Plate Freehand Sole Plate Attachment Circle Cutter Attachment Circle Cutter Installation Adapter Router Base Attachment 1/8” Collet 1/4” Collet 1/8” Lateral Style Drywall Cutter has "000028 HSS 1/8" marked on the shank of cutter 1/8”...
Page 8: Know Your Spin Saw
KNOW YOUR SPIN SAW...
Page 9: Assembly & Operation
ON / OFF SWITCH This spin saw is equipped with a sliding ON / OFF switch (1) located on the top of the tool (see Fig. 1). Fig. 1 1.
Page 10 INSTALLING FREEHAND SOLE PLATE – cont’d 1. Remove accessory locking knob (1) from the base of the spin saw motor housing (see Fig. 4). Slide freehand sole plate mounting bracket (2) onto the bottom of motor housing (3) until the mounting hole (4) lines up with the hole in the motor housing.
Page 11 PRACTICE CUTS USING FREEHAND SOLE PLATE Before attempting to work on an actual project, take the time to make a few practice cuts with your spin saw. Use some scraps of material that are the same material as used in your actual project.
Page 12 ASSEMBLY & OPERATION CUTTING OUTLET OPENINGS IN DRYWALL DANGER Do not attempt to use this tool to make cut-outs around any fixture or opening which has live electrical wires or on any wall which may have electrical wiring behind it. If a live wire is contacted, the bit could conduct the electric current to the tool, creating an electrocution hazard for the operator.
Page 13 1. Remove accessory locking knob (1) from the base of the spin saw motor housing (see Fig. 10). Slide precision handle mounting bracket (2) onto the bottom of motor housing (3) until the mounting hole (4) lines up with the hole in the motor housing.
Page 14 ASSEMBLY & OPERATION CIRCLE CUTTER CIRCLE CUTTER OPERATION WARNING Unplug the tool from the power source before changing accessories, changing bits and making adjustments. Before turning the tool ON, check to make sure bit and all accessory fasteners are securely tightened. 1.
Page 15 ASSEMBLY & OPERATION ROUTER BASE The router accessory converts your spin saw into a small hobby router that is capable of handling small ¼” shank router bits as well as the spiral cutting bit. The tilting base is ideal for bevel cutting.
Page 16 FREEHAND CUTTING AND ROUTING When the router base accessory is installed on the spin saw, it will function as a small router to be used for freehand cutting of irregular shaped patterns. You can cut patterns out of the workpiece with the cutting bit or route patterns into the workpiece with small router bits.
Page 17: Maintenance
LUBRICATION All of the bearings in this spin saw are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal conditions. Therefore, no further...
Page 18: Warranty
Model PT301H TWO (2) YEAR LIMITED WARRANTY FANTOM warrants this product to be free from defects in material and workmanship for a period of two (2) years from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions.