Subscribe to Our Youtube Channel
Summary of Contents for Erskine Attachments Mini Earth Auger
- Page 1 Mini Hydraulic Earth Auger Mini Skid Steer Loaders Mini Track Loaders Operator’s Manual Maintenance Parts Information Read this Manual Before Use...
-
Page 2: Table Of Contents
Serial Number………….. YOUR ATTACHMENTS DEALER ADDRESS: PHONE: CONTACT: NOTE: Erskine Attachments LLC reserves the right to make improvements in design or changes in specifications at any time without notice and without incurring any obligations to install them on units previously sold. -
Page 3: Safety
Indicates potentially Erskine Attachments LLC cannot anticipate every hazardous situation which, if not avoided, possible circumstance that might involve potential will result in death or serious injury. hazard. The safety messages found in this manual ... - Page 4 Keep all shields, guards, and covers in place. Avoid the hazard by relieving the pressure Do not modify equipment or add attachments that are not approved by Erskine Attachments LLC. before disconnecting hydraulic lines. Use adequate safety warning lights and devices as Use a piece of paper or cardboard, NOT BODY PARTS, to check for suspected leaks.
-
Page 5: Serial Number/Decal Location
SERIAL NUMBER AND SAFETY DECAL LOCATIONS Serial Number Location: It is important to refer to the serial number of the attachment when making repairs or ordering parts. Early or later models (identification made by serial number) may use different parts, or it may be necessary to use different procedures in doing a specific operation. - Page 6 Quantity: 2 Location: On front of yoke Quantity: 1 Safety Decals Locations: The locations of the safety decals are shown. If these decals are missing, damaged, or painted over they must be replaced. Call Erskine Attachments LLC (218-435-4045) for replacement decals.
-
Page 7: Mounting Instructions
MOUNTING INSTRUCTIONS After the initial set-up assembly is completed, use the following procedure to mount the attachment to the loader. Coupler wedges or pins must extend through the holes in the attachment mounting plate. Levers must be fully down and locked. Failure to secure wedges or pins can allow the attachment to come off and cause injury or death. - Page 8 MOUNTING INSTRUCTIONS Connecting Hydraulics: 1. Connect the hydraulic quick couplers from the attachment to the loader. IMPORTANT: Wipe the ends of the hydraulic quick couplers (both lead and loader) with a rag to remove possible contamination. Contamination can cause hydraulic components to fail and is not covered under warranty.
-
Page 9: Operating Instructions
OPERATING INSTRUCTIONS 1. With the operator in the operator’s position, the Contact with underground gas or seat belt fastened, and the seat bar lowered (if electric utilities can cause serious injury or so equipped), start the engine. death. To avoid injury or death, keep people away from... -
Page 10: Routine Maintenance
ROUTINE MAINTENANCE Lower the attachment to rest flat on the ground, shut down the engine, relieve the hydraulic pressure to the attachment, set park brake, and wait for all motion to stop before leaving the operator’s position to perform service of any kind. It is the operator’s responsibility to make daily inspections of the attachment and machine carrier for damage, loose bolts, fluid leaks, or anything else that could cause a potential service or safety problem. - Page 11 ROUTINE MAINTENANCE Lateral Swing Lock The auger is equipped with a lateral swing lock bolt to prevent the auger from swinging side-to-side. This bolt is located on the back side of the auger drive yoke. Be sure to remove this bolt for applications where side-to-side movement is desired.
-
Page 12: Parts Information
PARTS INFORMATION ITEM PART NO. DESCRIPTION STOCK NO. 319696 BOOM MINI EA W/A 319694 MOTOR YOKE MINI EA W/A 319695 CROSS YOKE MINI EA W/A 313756 MOUNT DRIVE W/A 311614 HUB MOTOR 1-5/8 TAPER 5-BOLT 319697 PIN 1 X 11.44 W/HOLE Z 316026 PIN 1 X 5 W/A 313776... - Page 13 PARTS INFORMATION...
-
Page 14: General Specifications
GENERAL SPECIFICATIONS Model Mini Earth Auger Operating Weight (w/out mount & bit) 165 lbs. 22.38” Overall Width (w/out mount & bit) 24.82” Overall Height (w/out mount & bit) 22.3” Overall Length (w/out mount & bit) 2” Hex Head Drive Style 30”... -
Page 15: Warranty
Erskine Attachments LLC to improve its products whenever it is possible and practical to do so. Erskine Attachments LLC reserves the right to make changes and or add improvements at any time without incurring any obligation to make such changes or add such improvements to products previously sold. - Page 16 P/N 300432 Date Printed: 9/10/2018 Printed in U.S.A. Erskine Attachments LLC...
Need help?
Do you have a question about the Mini Earth Auger and is the answer not in the manual?
Questions and answers