1. Manuals
  2. Brands
  3. Cookson Manuals
  4. Measuring Instruments
  5. Phantom Featheredge 6,225,768
  6. Owner's manual

Cookson Phantom Featheredge 6,225,768 Owner's Manual

Wireless self monitoring sensing edge system
Hide thumbs
Table of Contents

Advertisement

Quick Links

COOKSON OWNER'S MANUAL
VERSION 6
WIRELESS SELF MONITORING
SENSING EDGE SYSTEM
PATENT NO. 6,225,768
9046.DWG ECN 1057 10/27/09 REV 6

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Phantom Featheredge 6,225,768 and is the answer not in the manual?

Questions and answers

Summary of Contents for Cookson Phantom Featheredge 6,225,768

  • Page 1 COOKSON OWNER'S MANUAL VERSION 6 WIRELESS SELF MONITORING SENSING EDGE SYSTEM PATENT NO. 6,225,768 9046.DWG ECN 1057 10/27/09 REV 6...

  • Page 2: Specifications

    SPECIFICATIONS COMPATIBLE WITH THE FOLLOWING OPERATORS: - MGJ / H / GH / FDO-A / FDO-B / FDO-A10 / MG / SG NOT COMPATIBLE WITH OTHER (RF) RADIO FREQUENCY DEVICES TRANSMITTER ENCLOSURE MATL:....POLYCARBONATE ENCLOSURE COLOR:...BLACK ENCLOSURE RATING:..NEMA 4 OPERATING TEMP:....-25° F TO 120° F OPERATING FREQUENCY:..315 Mhz MAX OPER DISTANCE:..50 FT POWER:........9 VOLT LITHIUM BATTERY...

  • Page 3: Theory Of Operation

    THEORY OF OPERATION GENERAL DESCRIPTION: The Phantom Edge is a self monitoring wireless (RF) sensing edge system. A special communication protocol between the transmitter and receiver allow for additional signals (other than edge activation) to be sent, such as battery condition and periodic communication checks.
  • Page 4 5) Be sure that the battery strap is connected and insert the lithium ion 9 Volt battery into the cover of the unit, and replace the cover. The green LED light should light indicating that the unit is functioning properly. 2 - Wire 4 - Wire Connections...
  • Page 5 START UP / TESTING PROCEDURES RECEIVER INITIAL POWER UP: (ON OPERATOR) The unit will be in "Supervised Mode": Constant pressure required on door CLOSE control - 2 LED's under the label will be lit. Hold closed door control: - (D3) "Transmitter Awake" (GREEN) LED will blink when edge is pressed. - (D8) "Signal Acquired"...

  • Page 6: Troubleshooting

    Open door several feet - Verify that unit is still in "Supervised Mode". Constant pressure required on door CLOSE control. Reconnect sensing edge to Transmitter. Unit will switch to "Normal Mode". - (D6) "Normal Mode" (GRN) LED will light. Door now requires momentary contact for CLOSE control.
  • Page 7 DOOR WON'T CLOSE OR REVERSES TO FULL OPEN WHEN IT ATTEMPTS TO CLOSE: 1) Receiver has no power and the Safety Edge relay output is "closed" as a result. - Ensure that a STEADY 24 VOLTS are present; if DC is used, the red lead must be "positive" polarity.
  • Page 8 TO TEST FOR A RF SHORT-RANGE PROBLEM BETWEEN THE TRANSMITTER AND THE RECEIVER: For a BRIEF TEST, turn on the transmitter's test mode switch, #8, and activate the safety edge to initiate a transmission. The transmitter will come on and stay on until the switch #8 is turned back off for normal operation.
  • Page 9 LABEL AND MANUAL INFORMATION 1) Labeling Requirement In accordance with the Section 15.19 of FCC Rules, a permanently attached label shall be affixed to every product in a conspicuous location with the following statement: "This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation."...
  • Page 10 WIRING DIAGRAM - LIFTMASTER GH/H WIRING DIAGRAM - LIFTMASTER MGJ WIRING DIAGRAM - LIFTMASTER - MGJ 3 PHASE WIRING DIAGRAM - FDO-A / FDO-B MICANAN WIRING DIAGRAM - PRO GH/H COOKSON WIRING DIAGRAM - FDO-A10 WIRING DIAGRAM - MG, MGHL, SGH...
  • Page 11 LIFTMASTER GH/H WIRING DIAGRAM WIRE NUT FROM TRANSFORMER WIRE NUT (FIELD INSTALLED) (REMOVE) ORANGE BROWN GREEN BLUE YELLOW BLACK PHANTOM EDGE RECEIVER...
  • Page 12 LIFTMASTER MGJ - SINGLE PHASE WIRING DIAGRAM WIRE NUT (FIELD INSTALLED) (REMOVE) BROWN ORANGE BLACK GREEN PHANTOM EDGE RECEIVER...
  • Page 13 LIFTMASTER MGJ - 3 PHASE WIRING DIAGRAM WIRE NUT TRANSFORMER (FIELD INSTALLED) WIRE NUT RED (REMOVE) ORANGE BLACK BLUE GREEN YELLOW PHANTOM EDGE RECEIVER...
  • Page 14 FDO-A/FDO-B OPERATOR WIRING DIAGRAM AUX TERMINAL BLOCK J2 CIRCUIT BOARD TERMINALS BROWN BLACK PHANTOM EDGE RECEIVER...
  • Page 15 MICANAN GH/H WIRING DIAGRAM (REMOVE) WIRE NUT (FIELD INSTALLED) ORANGE YELLOW GREEN BLUE BLACK PHANTOM EDGE RECEIVER...

  • Page 16: Wiring Diagram

    FDO-A10 WIRING DIAGRAM WALL MOUNTED CONTROL PANEL WIRE NUT (FIELD INSTALLED) YELLOW FROM TERMINAL 14 ON CLOSE CONTACTOR GREEN ORANGE BLACK BLUE BROWN PHANTOM EDGE RECEIVER...
  • Page 17 COOKSON MG & SG SERIES OPERATOR WIRING DIAGRAM WALL MOUNTED CONTROL PANEL BLACK GREEN BROWN ORANGE BLUE PHANTOM EDGE RECEIVER...

Table of Contents