CGS Nationwide Industries PROTECTOR NW6149 Installation, Adjustment And Maintenance Instructions

www.nationwideindustries.com
The PROTECTOR Round Post Adapter Kit is designed to mount the
PROTECTOR MAGNETIC GATE LATCH to a 1-3/8" or 1-5/8" dia. Gate
R
and standard range of Post dia's.
A set of Shims have been provided to fit the most commonly used Fence
Post and Gate sizes. However, a 1-3/8" dia. Gate on a 2" dia. Post does
not require Shims.
1-5/8" Gate Shim
(as required)
Gate Post
Keeper
Bracket
Keeper Mtg Screw
#10 x 1/2" Panhead
Gate Side
Screw
Fig. 1
Note:
Also Review The Protector Gate Latch Installation Sheet
STEP 1 - Marking the Mounting Location:
1. Attach the Protector Keeper Assembly to the Keeper Bracket (Fig. 1).
R
Slide the NEW Upper & Lower Post Brackets into Gate Latch rear
groove as shown (Fig. 3). Align the Gate Latch and Lower Post
Bracket alignment holes and secure with #8 FlatHead Screw (Fig. 8).
2. Assemble the Keeper and Latch in the LATCHED POSITION (Fig. 3).
3. Using the ENTIRE Assembly as a Template, Locate as shown (Fig. 3
& 4) and MARK the Location of the Keeper Bracket and the Upper &
Lower Post Brackets.
4. Unlock Keeper from Latch. Remove the Keeper from Bracket. Remove
Upper & Lower Brackets from Latch.
Using each bracket as a Template, return Brackets to the respective
location and mark each mounting hole location (Fig. 4). Make sure to
locate holes on the centerline of the Post.
Note: The Adapter Kit includes Self-Drilling Mounting screws, but
to ease installation, we suggest drilling pilot holes.
Liability Limitation & Warranty: This product is inspected prior to shipment and
is warranted to the original purchaser to be free from defects in material and
workmanship. No warranty applies if the product has been tampered with or
damaged by the purchaser, and in no case shall the manufacturer or supplier
be liable for damages which are incidental or consequential.
THE PROTECTOR ROUND POST ADAPTER KIT
INSTALLATION, ADJUSTMENT AND MAINTENANCE INSTRUCTIONS
PLEASE CAREFULLY READ ALL OF THE
INSTRUCTIONS PRIOR TO INSTALLATION
R
(3) 2-3/8",
Bracket Mtg Screw
#10 x 3/4" Drill Pt
Panhead Screw
Keeper Mtg Screw
#10 x 5/8" Panhead
Screw
Bracket Mtg Screw
#10 x 3/4" Drill Pt
Flathead Screw
Protector Keeper
R
Assembly
R
NW6149
R
2-5/8"
or 2-7/8"
Post Shims
(as required)
Post Side
Bracket Mtg Screw
#10 x 3/4" Drill Pt
Panhead Screw
SHEET 1 OF 2
Disclaimer: The manufacturer and supplier of this device cannot and will not accept
responsibility for unauthorized modifications to or for defective maintenance of this
device. No modification to this device whatsoever is to be made other than with
respect to the adjustments outlined in this installation instruction. If this device fails
to function properly, it should be returned promptly to the supplier for replacement.
REV. 00 05-02-08
Fig. 3
Fence Post
Upper & Lower
Brackets
Fig.2
Lower Bracket
Alignment Holes
Keeper
Bracket
C L
Keeper
Bracket
Lower Post
Bracket
Fig. 4
BY: CGS
Gate
Latch
Upper
Post
Bracket
Lower Post
Bracket
Upper Post
Bracket
Min: 6.0"
Max: 11.0"
Normal: 7.5"
C L
1/2"