Bosch DWB98JR50A User Manual And Installation Instructions page 7

6.11 Setting the sensor control
Requirement: The appliance is switched off.
Press and hold ​ ⁠ .
1.
a The setting is displayed after approx. one second.
Press ​ ⁠ , ​ ⁠ , ​ ⁠ , ​ ⁠ or
2.
3. Release ​ ⁠ to save the setting.
6.12 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡ After the appliance has been switched off,
appears on the display for the grease filter.
¡ After the appliance has been switched off,
appears on the display for the odour filter.
Press ​ ⁠ .
▶
a The saturation indicator is reset.
6.13 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement: The appliance is switched off.
1. Press and hold
To set circulating-air mode (non-regenerative fil-
‒
ter), press ​ ⁠ .
7 Home Connect
This appliance is network-capable. Connecting your ap-
pliance to a mobile device lets you control its functions
via the Home Connect app, adjust its basic settings
and monitor its operating status.
The Home Connect services are not available in every
country. The availability of the Home Connect function
depends on the availability of Home Connect services
in your country. You can find information about this at:
www.home-connect.com.
The Home Connect app guides you through the entire
login process. Follow the instructions in the Home Con-
nect app to configure the settings.
Tips
¡ Please consult the documents supplied by
Home Connect.
¡ Please also follow the instructions in the Home Con-
nect app.
Notes
¡ Please note the safety precautions in this instruction
manual and make sure that they are also observed
when operating the appliance via the Home Con-
nect app.
→ "Safety", Page 2
¡ Operating the appliance on the appliance itself al-
ways takes priority. During this time it is not possible
to operate the appliance using the Home Connect
app.
¡ In networked standby mode, the appliance requires
a maximum of 2 W.
¡ If you need your device's MAC address to connect
to your home network, you can find this next to the
rating plate. → Page 11
​ ⁠ to change the setting.
​ ⁠ .
To set circulating-air mode (regenerative filter),
‒
press ​ ⁠ .
To set air extraction mode, press ​ ⁠ .
‒
Release
2.
6.14 Switching on the lighting
The lighting can be switched on and off independently
of the ventilation system.
Press
▶
6.15 Setting the brightness
Press and hold
​ ⁠ and 1 ▶
reached.
​ ⁠ and 2
6.16 Switching on the audible signal
Requirement: The appliance is switched off.
Press and hold
▶
prox. three seconds until a signal sounds.
6.17 Switching off the signal tone
Requirement: The appliance is switched off.
Press and hold
▶
prox. 3 seconds.
a A signal tone will sound.
7.1 Setting up Home Connect
Requirements
¡ The appliance is connected to the power supply and
is switched on.
¡ You have a mobile device with a current version of
the iOS or Android operating system, e.g. a smart-
phone.
¡ The mobile device and the appliance are within
range of your home network's Wi-Fi signal.
Download the Home Connect app.
1.
Open the Home Connect app and scan the follow-
2.
ing QR code.
Follow the instructions in the Home Connect app.
3.
​ ⁠ to save the setting.
​ ⁠ .
​ ⁠ until the required brightness is
​ ⁠ and ​ ⁠ at the same time for ap-
​ ⁠ and ​ ⁠ at the same time for ap-
Home Connect en
7