STI EZ-Path 33 Series Installation Sheet

GENERAL -
READ COMPLETELY BEFORE INSTALLING
(Part No. EZP133K & EZDP133FK* )
This product is designed to facilitate
®
installation of the Series 33 EZ-Path Fire
Rated Pathway (Cat. No. EZD33FWS) in
cored openings through walls and floors.
Plate when inserted into opening, utilizes
built-in locking mounting clips to securely
fasten it within the opening. No additional
fasteners are required.
NOTE: This product is designed for use in accurately cored 4" (102 mm) diameter openings
in concrete floors or walls. Installation of this plate requires a minimum unobstructed area of
3/4" (20 mm) completely around the cored opening. Plate pathway opening is asymmetrical
(keyed) and plate and pathway must be aligned. Rotate plate until the stamping "EZP133K"
aligns with the lid (labeled side) of pathway.

INSTALLATION INSTRUCTIONS

1. Start all set screws into flanges on the plate.
2. Apply pressure to the plate, with the foam wedges facing the opening, until the plate is
flush with the top surface of the floor or one surface of the wall (See Fig 1).
3. Slide pathway into keyed plate, with label side going in first, and set it to the floor
or wall thickness. (See Fig 2). Secure plate to pathway by tightening set screws.

ALTERNATE INSTALLATION INSTRUCTIONS

1. Start all set screws into flanges on the plate.
2. Slide kick-in plate over pathway, making sure that pathway retaining flanges face
outward. Adjust plates to wall or floor thickness. Secure plate to pathway by
tightening set screws (See Fig 3).
3. Insert pathway slowly into opening until mounting clips contact the wall or floor
surface exercising care to make sure that the pathway is centered and properly
aligned with the opening. Apply pressure to the pathway until the mounting
clips lock into place within the opening and the plate rests flush with the surface
of the floor or wall (See Fig 4).
Page 1 of 2 Installation Sheet • Kick-In Plate
INSTALLATION SHEET
Kick-In Plate

TABLE A: Parts List

Qty. Description
1 Kick-In Plate
2 Ground Screws
1 5/64" Allen Key
10 8-2 x 1/4" lg. Set Screws
EZD33FWS*
1
*Available in the EZDP133FK
FIG 1
FIG 2
FIG 3
FIG 4
ZIS1006-3345
GENERAL -
READ COMPLETELY BEFORE INSTALLING
(Part No. EZP133K & EZDP133FK*)
This product is designed to facilitate
®
installation of the Series 33 EZ-Path Fire
Rated Pathway (Cat. No. EZD33FWS) in
cored openings through walls and floors.
Plate when inserted into opening, utilizes
built-in locking mounting clips to securely
fasten it within the opening. No additional
fasteners are required.
NOTE: This product is designed for use in accurately cored 4" (102 mm) diameter openings
in concrete floors or walls. Installation of this plate requires a minimum unobstructed area of
3/4" (20 mm) completely around the cored opening. Plate pathway opening is asymmetrical
(keyed) and plate and pathway must be aligned. Rotate plate until the stamping "EZP133K"
aligns with the lid (labeled side) of pathway.
INSTALLATION INSTRUCTIONS
1. Start all set screws into flanges on the plate.
2. Apply pressure to the plate, with the foam wedges facing the opening, until the plate is
flush with the top surface of the floor or one surface of the wall (See Fig 1).
3. Slide pathway into keyed plate, with label side going in first, and set it to the floor
or wall thickness. (See Fig 2). Secure plate to pathway by tightening set screws.
ALTERNATE INSTALLATION INSTRUCTIONS
1. Start all set screws into flanges on the plate.
2. Slide kick-in plate over pathway, making sure that pathway retaining flanges face
outward. Adjust plates to wall or floor thickness. Secure plate to pathway by
tightening set screws (See Fig 3).
3. Insert pathway slowly into opening until mounting clips contact the wall or floor
surface exercising care to make sure that the pathway is centered and properly
aligned with the opening. Apply pressure to the pathway until the mounting
clips lock into place within the opening and the plate rests flush with the surface
of the floor or wall (See Fig 4).
Page 1 of 2 Installation Sheet • Kick-In Plate
INSTALLATION SHEET
Kick-In Plate
TABLE A: Parts List
Qty. Description
1 Kick-In Plate
2 Ground Screws
1 5/64" Allen Key
10 8-2 x 1/4" lg. Set Screws
EZD33FWS*
1
*Available in the EZDP133FK
FIG 1
FIG 2
FIG 3
FIG 4
ZIS1006-3345