Table of Contents
Advertisement
Available languages
Available languages
English
Preparing Power Cleaner Unit for Use
DANGER: Risk of fluid injection and laceration.
When using the high‑pressure setting, DO NOT allow
the high‑pressure spray to come in contact with
unprotected skin, eyes, or with any pets or animals.
Serious injury will occur.
CAUTION: Before operation:
•
Connect the water supply to the power cleaner.
For instructions on connecting the water supply
to the power cleaner, please refer to Attaching
garden or suction hose under Assembly
and Adjustments.
•
Connect the attachment. For instructions on
connecting the pressure spray wand, please
refer to Attachments under Assembly
and Adjustments.
Preparing the Power Cleaner (Fig. L)
iMPORTAnT: Disengage the trigger lock‑off
trigger
6
and hold the trigger for 30 seconds to purge the
system of air. If air is still found in the water stream, continue to
run water through the spray handle.
1. Disengage the trigger lock‑off
2. Squeeze the trigger
6
.
Cleaning a Surface (Fig. L)
WARNING: Risk of injury from spray. Always engage
the trigger lock when gun is not in use. Failure to do so
could cause accidental spraying.
1. To start the power cleaner, disengage the trigger
lock‑off
4
and squeeze the trigger
nOTE: The best angle for spraying water against a
cleaning surface is 45 °. Spraying head on tends to cause
dirt particles to embed in the surface. When working on
vertical surfaces, it is best to apply detergent starting at
the bottom and working upwards which will prevent the
detergent from sliding down and causing streaks.
2. To stop the power cleaner, release the trigger.
nOTE: Excessive pump pressure may be the result of
clogged nozzle. Always turn off the power cleaner and
remove the battery before attempting to unclog a nozzle
WARNING: Never draw from water that contains
chemicals. Only draw from fresh water sources.
Shutdown (Fig. A)
1. To stop the power cleaner, release the trigger and remove
the battery.
2. Turn off water at the faucet.
3. Discharge residual pressure by squeezing the trigger
until no more water comes out of the spray wand
4. Disconnect the garden hose from the water intake
drain hose.
5. Remove garden hose from power cleaner by pulling
back the collar on the quick connect hose adapter and
removing it from the quick connect filter.
12
4
,squeeze the
4
.
6
.
6
8
.
3
and
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Nozzle (Fig. A, H)
If the nozzle
10
becomes clogged with foreign materials,
such as dirt, excessive pressure may develop. If the nozzle
becomes partially clogged or restricted, the pump pressure
will pulsate. Clean the nozzle immediately.
1. Shut off the power cleaner
battery and turn off the water supply.
2. Pull trigger
6
on main handle
water pressure.
3. Open the nozzle as wide as it will open.
4. Unclog any debris from the nozzle.
5. Run water from a faucet or garden hose through
the nozzle.
Suction Hose (Fig. N)
1. To clean the suction hose
power cleaner.
2. Pull trigger switch to relieve any water pressure.
3. Decouple the suction hose
4. To clean the suction hose, use water from a garden hose
to thoroughly rinse out the suction hose and allow it
to dry.
Suction Hose Filter (Fig. N)
•
Turn the filter
20
on the end of the suction hose
counterclockwise and remove. Remove the strainer from
inside of the filter. Rinse all of the parts with clean water
and reassemble.
Quick Connect Filter (Fig. O)
1. Pull back the collar on the quick connect hose
adapter
13
and remove the garden or suction hose from
the quick connect filter
7
2. Remove the quick connect filter from the power cleaner.
3. Inside the quick connect filter
Remove the screen filter and rinse with clean water
and reassemble.
2
and and remove the
1
to relieve any
12
, shut off the
12
from the power cleaner.
12
.
7
is a screen filter
21
.
Advertisement
Table of Contents
