Page 2
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 客户确认反馈 Feedback of customer’s Confirmation 经确认,我方承认该规格书 We accept the specification after Confirmed 客户名称 客户签字 确认日期 Customer name Customer signature Confirmation Date 请签字后将此页与首页按以下地址回传我公司,谢谢! Please feed back this paper and first paper after your signature by the address,thanks! 地址:四川省绵阳市安州工业园区...
Page 3
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 更改记录 Record of Modification 更改日期 主要更改内容 更改原因 更改通知编号 序号 确认 Date of Main content of Reason of Serial number of Confirm modification modification modification modification 2018/03/06 首次承认 黄伟 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 3 of 16...
Page 4
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 1. Introduction WF-Q379-USA1 module design is based on Qualcomm 9379-7 solution, The QCA9379-7 is a highly integrated single chip which has built in a 2x2 dual-band wireless LAN radio. The Module is a highly integrated MAC/BBP and 2.4/5GHz PA/LNA single chip which supports a 866.7Mbps PHY rate.
Page 5
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 1.2 Specification reference This specification is based on additional references listed below. _ IEEE Std. 802.11a _ IEEE Std. 802.11b _ IEEE Std. 802.11g _ IEEE Std. 802.11n _ IEEE Std. 802.11ac 1.3 System Functions Table1: General Specification as below: Qualcomm QCA9379-7 Main Chipset...
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 2. Mechanical Specification 2.1 Mechanical Outline Drawing Typical Dimension (W x L x H): 18.0mm x 27.0mm x 3.0mm General tolerance: ±0.15mm 2.2 Pin definition TOP VIEW 四川爱联科技有限公司 Sichuan AI-Link Technology Co.,Ltd. page 6 of 16...
WF-Q379-USA1 IEEE 802.11a/b/g/n/ac 2T2R USB WIFI Module 4. Software Requirements The driver supports the following operating systems: Linux, Microsoft Windows XP, Vista and Win7. Mfg. software tool is QDART. 5. Antenna matching The BT RF ,ANT0 and ANT1 Pin connect to antenna, please refer to design demand a).
Page 17
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 18
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules Part 15.247 and Part 15.407 2.3 Specific operational use conditions The module is limited to installation in mobile or fixed application. A separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and difference antenna configurations.
Page 19
modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product. 2.10 Additional testing, Part 15 Subpart B disclaimer This modular transmitter is only FCC authorized for FCC Part 15.247&15.407 as listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.