Related Manuals for BARKER AND STONEHOUSE TENBY T3NBDINIGREY
Summary of Contents for BARKER AND STONEHOUSE TENBY T3NBDINIGREY
- Page 1 ASSEMBLY INSTRUCTIONS TENBY 1.5M ROUND FIREPIT DINING TABLE SKU: T3NBDINIGREY BSH-FPT-150G-1005G IMPORTANT NOTICE THIS BOOKLET CONTAINS USEFUL INFORMATION ABOUT WARRANTY & CARE INSTRUCTIONS. PLEASE KEEP FOR FUTURE REFERENCE.
-
Page 2: Parts List
ASSEMBLY INSTRUCTIONS PARTS LIST Table Box Part Part Name Leg Panel Table Top Side Panel With Door Side Panel With Control Hole Glass M6 x 20mm Screw Washer Allen Key... - Page 3 ASSEMBLY INSTRUCTIONS PARTS LIST Firepit System Box Windguard Box Part Part Name Firepit System Stainless Steel Lid Cover Onyx Coloured Fireglass Round Windguard Panel Top Connector For Windguard Bottom Connector For Windguard...
- Page 4 • Please only use this product for its intended purpose as outdoor furniture within a residential environment. Failure to do so will void your warranty. • Barker And Stonehouse holds no responsibility for any damages caused due to normal wear and tear, incorrect assembly, misuse and/or negligence.
- Page 5 ASSEMBLY INSTRUCTIONS GAS FIREPIT SAFETY ADVICE - READ BEFORE YOU START! ONLY a 5kg Patio Gas Bottle can be used in conjunction with this firepit. • Using any other size will invalidate your warranty and will damage your product. • Perform a visual inspection of all fixings ensuring they are all securely tightened before using the system for the first time.
- Page 6 ASSEMBLY INSTRUCTIONS TABLE ASSEMBLY STEP 1 Loosely secure the leg panel onto the table top using the M6 x 20mm screws and washers. Do not tighten any screws at this step.
- Page 7 ASSEMBLY INSTRUCTIONS TABLE ASSEMBLY STEP 2 Loosely secure the second leg panel onto the table top using the M6 x 20mm screws and washers. Do not tighten any screws at this step.
- Page 8 ASSEMBLY INSTRUCTIONS TABLE ASSEMBLY STEP 3 Loosely secure the side panel with door to the inside of the legs using the M6 x 20mm screws and washers. Do not tighten any screws at this step.
- Page 9 ASSEMBLY INSTRUCTIONS TABLE ASSEMBLY STEP 4 Loosely secure the side panel to the inside of the legs using the M6 x 20mm screws and washers. ITS TIME! Now tighten all the screws with the provided Allen key.
- Page 10 ASSEMBLY INSTRUCTIONS TABLE ASSEMBLY STEP 5 Turn the table over and add the glass to the table ensuring the suctions cups are flat . COMPLETE! SAFETY WARNING! Assembly of the table is now Always lift and secure the glass with complete! two people.
- Page 11 ASSEMBLY INSTRUCTIONS FIREPIT SYSTEM ASSEMBLY STEP 1 Remove the firepit system control panel nuts. Keep the nuts to one side.
- Page 12 ASSEMBLY INSTRUCTIONS FIREPIT SYSTEM ASSEMBLY STEP 2 Lower the gas firepit system into the centre of the table, on top of the glass. Position the regulator, hose and control panel through the table hole before lowering the system onto the glass edge. SAFETY WARNING! Ensure the gas pipes under the table are not kinked and all wiring...
- Page 13 ASSEMBLY INSTRUCTIONS FIREPIT SYSTEM ASSEMBLY STEP 3 Attach the firepit control panel to the table base frame. Tighten the control panel onto the frame using the nuts previously removed in step 1.
- Page 14 ASSEMBLY INSTRUCTIONS FIREPIT SYSTEM ASSEMBLY STEP 4 Carefully fill the firepit system with the fireglass. Ensure the pilot cover is not obstructed. Position the firepit lid into the space around the firepit centre. (Always remove the lid before lighting the firepit).
- Page 15 ASSEMBLY INSTRUCTIONS FIREPIT SYSTEM ASSEMBLY STEP 5 Remove the battery cover. Place 1 x AAA battery into the ignition, ensuring the negative side is inserted first. Once inserted, add the battery cover back onto the control panel. Negative End Positive End COMPLETE! Assembly of the firepit system is now complete!
- Page 16 ASSEMBLY INSTRUCTIONS WINDGUARD ASSEMBLY STEP 1 Loosen all the grub-screws in the connectors with a Phillips screwdriver (not supplied). Loosely position each windguard panel, one at a time, using the top and bottom connectors until a round windguard is formed. Do not tighten any screws until the windguard is formed.
- Page 17 ASSEMBLY INSTRUCTIONS WINDGUARD ASSEMBLY STEP 2 Once the windguard is formed tighten all the grub screws using a Phillips screwdriver and position the windguard roughly 2 cm around the edge of the firpit system. SAFETY ADVICE! We recommend tightening the grub-screws occasionally after use.
- Page 18 ASSEMBLY INSTRUCTIONS GAS FIREPIT SYSTEM LEAK TEST NEVER USE AN OPEN FLAME TO TEST FOR LEAKS AT ANYTIME. A GAS LEAK TEST MUST BE PERFORMED BEFORE FIRST USE OF THE GAS FIREPIT SYSTEM. (Perform in a well ventilated area) 1. Confirm all appliance control knobs are in the off position. 2.
- Page 19 ASSEMBLY INSTRUCTIONS BEFORE LIGHTING YOUR FIREPIT • Check all fixings on the gas firepit system are securely tightened before first use. • Ensure a 5kg patio gas bottle is used with the gas firepit system. • Ensure the gas bottle measures no more than 39cm tall.
- Page 20 ASSEMBLY INSTRUCTIONS BEFORE LIGHTING YOUR FIREPIT • Check the table is positioned on flat, solid ground. • 1 x AAA battery must be inserted into the ignition, position within the control panel. • Ensure the black wire from the system is connected to the igniter.
- Page 21 ASSEMBLY INSTRUCTIONS BEFORE LIGHTING YOUR FIREPIT • Ensure all gas pipes are not bent or kinked. • Ensure the regulator is facing down, once the gas bottle is connected • Make sure the table is used outdoors in a well ventilated area.
-
Page 22: Care And Maintenance
ASSEMBLY INSTRUCTIONS CARE & MAINTENANCE Please read the below Care & Maintenance tips to help protect your garden table: • To prolong the life of the tabletop we recommend you always use place mats and coasters when putting glasses and plates onto the glass. •... - Page 23 ASSEMBLY INSTRUCTIONS...
Need help?
Do you have a question about the TENBY T3NBDINIGREY and is the answer not in the manual?
Questions and answers