DVDO DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual Introduction Overview This product is an HDBaseT 2.0 wall plate transmitter for HDMI inputs and HDBaseT 2.0 output. HDMI signals up to 4K@60 (YUV 4:2:0 color sub-sampling). It supports signal transmission up to 90m/300ft for 4K and 100m/330ft for 1080P via signal Cat 5e/6 cable, and supports signal transmission up to 100m/330ft for 4K and 1080P via single Cat 6a/7 cable.
DVDO DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual Features Three HDMI inputs and one HDBT output Auto switching technology One-way analog audio pass-through from transmitter to receiver Via Cat 6/6a/7 cables, transmits 4K@60Hz (YUV 4:2:0 color sub-sampling) ...
DVDO DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual Package Contents Before you start the installation of the product, please check the package contents as below: DVDO-Xtend-TX100 Transmitter x 1 Phoenix Male Connector (2 Pins, 3.5mm) x 1 ...
DVDO DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual Installation and Wiring Warnings: Before wiring, disconnect the power from all devices. During wiring, connect and disconnect the cables gently. Steps for device wiring: Connect HDMI sources (such as Blu-ray, DVD, HDD, camera, games console, Satellite/cable TV, computer, media server etc.) to the Transmitter.
DVDO DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual Input Switching The transmitter supports automatic switching and front panel button switching. When it is powered on, automatic switching will function as follows: When HDMI sources are inserted, the switcher will follow the rule: last in, first out, switch to the latest connected source for output display.
DVDO DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual API Command Control Users can control the device via sending API commands as well. Please refer to the following steps. Connect the HDBT OUT of the transmitter to HDBT IN of receiver, the transmitter can be powered by receiver via Cat X cable.
Page 15
DVDO DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual Click Open, the button will become red for operation. Type the commands in the data transmit window, for example “GET SW_VERSION”, click your PC Enter button and click the Uart Tool Send button, the Data receive window will show the response.
DVDO DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual DVDO Product Configuration Tool The transmitter supports configuration through the “DVDO Product Configuration Tool”. Connect the HDBT OUT of the transmitter and your receiver HDBT IN, the transmitter can be powered by receiver via Cat X cable.
Page 17
DVDO DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual “DVDO Product Configuration Tool” menus are described below: • Get current settings: Get the current settings of the sink device. • Baud rate: Choose the correct baud rate according to the device, then click “Connect”...
DVDO DVDO-Xtend-TX100 3 x 1 HDBT Wall-plate Transmitter User Manual Warranty Terms and Conditions For the following cases we shall charge for the service(s) claimed for the products if the product is still remediable and the warranty card becomes unenforceable or inapplicable.
Need help?
Do you have a question about the DVDO-Xtend-TX100 and is the answer not in the manual?
Questions and answers