Subscribe to Our Youtube Channel
Summary of Contents for ITech DF2.2
- Page 1 DRY FILTER SPRAYBOOTH INSTALLATION & MAINTENANCE INSTRUCTIONS Scott+Sargeant Woodworking Machinery Ltd 1 Blatchford Road, Horsham, West Sussex RH13 5QR ENGLAND Tel +44 (0) 1403 273000...
-
Page 3: Table Of Contents
Dry Filter Spraybooth Installation and Maintenance Instructions CONTENTS Type, Designation and Identification……………………………………… Uses of the Machine……………………………………………………….. Identification of Working Areas…………………………………………... Delivery and Handling ……………………………………………………. Inspection………………………………………………………………….. Warranty………………………………………………………………… Assembly and Installation…………………………………………………. Exhaust Ducting…………………………………………………………… Noise………………………………………………………………………. Electrical Data……………………………………………………………... Electrical Connections…………………………………………………….. Siting of Electrical Controls……………………………………………….. Fitting of Filters……………………………………………………………... -
Page 5: Type, Designation And Identification
DF - The DF range of Booth are Dry Filter Spraybooths with an open-fronted configuration available in a range of widths from 2.2metres to 6.6metres e g. DF2.2 Dry Filter Spraybooth 2.2metres wide. DFB - The DFB range of Booths are 1.1metre deep Dry Filter Spraybooths complete with an operators Bench. In these Booths the filter medium is mounted above the operator’s bench and angles forward at approximately 30°. -
Page 6: Delivery And Handling
Please refer to the following table for information on shipping weights of complete Spraybooths and individual Spraybooth components. Model Shipping Fan Weight Individual Panel Pack of Filter Weight Weight Paper DF2.2 DF3.3 DF4.0 DF4.4 2 x 88 DF5.5 2 x 90 DF6.6 2 x 90 DFB1.1 DFB2.2... -
Page 7: Inspection
Dry Filter Spraybooth Installation and Maintenance Instructions Airflow Spraybooths are usually delivered to site in component form. Components are either banded to pallets or manufactured in such a way so as to enable transportation by forklift truck. Fan units are equipped with holes for the connection of suitable shackles, and should be lifted into position by use of suitable proprietary lifting equipment (as diagram below). -
Page 8: Exhaust Ducting
Dry Filter Spraybooth Installation and Maintenance Instructions of panel joints. If the Booth canopy is to form part of a dust free environment the panel joints may be sealed with a proprietary high velocity duct sealant. Exhaust Ducting Exhaust ducting venting an Airflow Spraybooth to atmosphere should be designed and installed by a competent ventilation engineer. -
Page 9: Electrical Connections
Dry Filter Spraybooth Installation and Maintenance Instructions The metal body of the motor, the switchgear control panel and, the fan unit must all be earthed. It is strongly recommended that an earth leakage circuit breaker with a tipping current of 30mA or less is fitted on the incoming electrical supply. -
Page 10: Fitting Of Filters
Dry Filter Spraybooth Installation and Maintenance Instructions In order to comply with the requirements of CE marking, all Spraybooths must now be fitted with a facility for an emergency stop within easy reach of the operator. Airflow will be pleased to quote for the supply of a suitable emergency stop wire kit, now available to meet the requirements of this regulation. -
Page 11: Operation
Dry Filter Spraybooth Installation and Maintenance Instructions 1. Ensure the Spraybooth and its Canopy has been assembled in accordance with the manufacturer’s instructions. Check that the Canopy is square and that its front edges are secured to the factory floor. 2. -
Page 12: Servicing
Dry Filter Spraybooth Installation and Maintenance Instructions the filter medium and with the Fan running coat the internal surfaces of the Booth canopy with Peelable Booth Coating. This will ensure that the following clean down is a quick and efficient operation. Servicing The only moving parts that require servicing on the Airflow range of Dry Filter Spraybooths is the Extraction Fan. -
Page 13: Spare Parts
Dry Filter Spraybooth Installation and Maintenance Instructions 1. Slide the cartridge arm into the fan casing until the shaft locates in the fan casing hole. Lower the cartridge by approximately 50mm into position. 2. Replace the four mounting bolts, ensuring that that the identical shims are placed in identical respective positions. 3. - Page 14 Dry Filter Spraybooth Installation and Maintenance Instructions CE EC DECLARATION OF CONFORMITY CE In accordance with The Supply of Machinery (Safety) Regulations 2008. This declaration relates to the range of Airflow spray booth. A full listing of which appear in the relevant technical file (See Section 1 of this Publication for type designation).
Need help?
Do you have a question about the DF2.2 and is the answer not in the manual?
Questions and answers