Download
Share
Print this page
  1. Manuals
  2. Brands
  3. iPort Manuals
  4. Network Hardware
  5. CONNECT PRO 72350
  6. Manual

iPort CONNECT PRO 72350 Manual

Wallstation
Hide thumbs

Advertisement

Quick Links

Download this manual
CONNECT
PRO
WA LLSTAT IO N
72350 - CONNECT PRO WallStation Black
72351 - CONNECT PRO WallStation White
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the CONNECT PRO 72350 and is the answer not in the manual?

Questions and answers

Summary of Contents for iPort CONNECT PRO 72350

  • Page 1 CONNECT WA LLSTAT IO N 72350 - CONNECT PRO WallStation Black 72351 - CONNECT PRO WallStation White...
  • Page 2 Station holding and charging the IPORT CONNECT Case. • Cover Plate - The removeable plastic cover that attaches to the WallStation, covering the label and Screws. • IPORT Security Tool - The orange handled 1.5mm hex tool used for locking and unlocking IPORT Products.
  • Page 3 CONNECT WA LLSTAT IO N WA L LSTAT I ON I N STA LL OPTIONS Before starting, detimine the install scenario that best describes your desired install. Then click on the title to be directed to the appropriate install steps. New Construction using Cat 6 Cable | pg.
  • Page 4 CONNECT WA LLSTAT IO N IPORT CONNECT Pro WallStation Install New Construction - Cat6 Before Construction is complete 1. Determine the desired location of the IPORT Connect Pro WallStation will live when the construction is completed.
  • Page 5 CONNECT New Constructions Cat6 WA LLSTAT IO N Install a 1 Gang electrical box or low voltage ring in the desired location of the WallStation. Electrical NOTE: The CONNECT PRO WallStation will cover a 1G electrical box only. A 2 Gang electrical box will interfere with the mounting hardware.
  • Page 6 CONNECT New Constructions Cat6 WA LLSTAT IO N Run a Cat6 cable terminated with an RJ45 Connectors (T568A or T568B) from the WallStation location to a nearby AC outlet, closet, or network rack location and terminate the other end of the cable the same as before.
  • Page 7 CONNECT New Constructions Cat6 WA LLSTAT IO N Installing the WallStation After Construction Terminate the Cat6 with an RJ45 Connector if not done so previously using T568A or T568B standards. Remove the WallSation, Drywall anchors and Screws from the box and place on a table.
  • Page 8 CONNECT WA LLSTAT IO N New Constructions Cat6 Insert the WallStation into the 1G box.
  • Page 9 CONNECT New Constructions Cat6 WA LLSTAT IO N 4. Use a leveling tool to level the WallStation and mark the 4 locations for the provided Anchors. Remove the WallStation from the 1G Box. Screw the 4 provided anchors into the wall where marked.
  • Page 10 CONNECT New Constructions Cat6 WA LLSTAT IO N Connect the RJ-45 to TE Connector provided to the Cat6 cable and onto the white TE connector WallStation DC Adapter. Label wire WARNING: Only for DC Low Voltage - Not for PoE Zip tie the Connector to the DC board for added cable retnetion.
  • Page 11 CONNECT WA LLSTAT IO N New Constructions Cat6 Insert the WallStation back into the 1G box and use the provided screws to attach the WallStation to the wall. IMPORTANT: Make Sure to position the WallStation with the Up Arrow facing up. Use a leveling tool to level the WallStation and hand tighten the screws.
  • Page 12 CONNECT New Constructions Cat6 WA LLSTAT IO N Attach the WallStation Cover Plate over the WallStation making sure to alight the positioning notch with the tooth on the WallStation.
  • Page 13 CONNECT WA LLSTAT IO N New Constructions Cat6 Connect the RJ-45 to DC Connector at the other end of the Cat6 Cable. 10. Connect the provided DC power adapter into the other end of the RJ-45 DC adapter and plug in the power adapter into an AC outlet.
  • Page 14 CONNECT WA LLSTAT IO N For a clean finished look place the Connector and DC barrel plug back throug the grommit into the wall. Grommit not included...
  • Page 15 CONNECT New Constructions Cat6 WA LLSTAT IO N Place a Case with an iPad installed onto the WallStation to determine power was installed properly and the iPad charges. COMPLETE...
  • Page 16 CONNECT WA LLSTAT IO N Installing the WallStation in Existing Construction - Cat6 Determine the desired location of the IPORT Connect Pro WallStation. Use a 2-3/4” (70mm) hole saw to cut a hole in the desired location of the WallStation...
  • Page 17 CONNECT WA LLSTAT IO N Existing Constructions Cat6 Insert the WallStation into the 2 3/4 - inch hole and use a leveling tool to level the WallStation. Mark the 4 locations for the provided Anchors. Remove the WallStation form the wall once you have marked the 4 anchor locations.
  • Page 18 CONNECT WA LLSTAT IO N Existing Constructions Cat6 Screw the provided anchors into the wall where marked.
  • Page 19 CONNECT Existing Constructions Cat6 WA LLSTAT IO N Use the 2 3/4 - inch hole to fish a Cat6 cable to a nearby AC outlet, closet or network rack. Grommit not included...
  • Page 20 CONNECT Existing Constructions Cat6 WA LLSTAT IO N Terminate both ends the Cat6 with an RJ45 Connector using T568A or T568B standards Label wire WARNING: Only for DC Low Voltage - Not for PoE Grommit not included...
  • Page 21 CONNECT Existing Constructions Cat6 WA LLSTAT IO N Connect the RJ-45 to TE Connector provided to the Cat6 cable and onto the white TE connector WallStation DC Adapter. Zip tie the Connector to the DC board for added cable retnetion.
  • Page 22 CONNECT Existing Constructions Cat6 WA LLSTAT IO N Insert the WallStation back into the wall and use the provided screws to attach the WallStation to the wall anchores. IMPORTANT: Make Sure to position the WallStation with the Up Arrow facing up. Use a leveling tool to level the WallStation and hand tighten the screws.
  • Page 23 CONNECT Existing Constructions Cat6 WA LLSTAT IO N 10. Attach the WallStation Cover Plate over the WallStation making sure to alight the positioning notch with the tooth on the WallStation.
  • Page 24 CONNECT WA LLSTAT IO N Existing Constructions Cat6 11. Connect the RJ-45 to DC Connector at the other end of the Cat6 Cable. 12. Connect the Provided DC Power Adapter into the wall and connect the barrel connector to the other end of of the RJ-45-DC adapter.
  • Page 25 CONNECT WA LLSTAT IO N For a clean finished look place the Connector and DC barrel plug back throug the grommit into the wall. Grommit not included...
  • Page 26 CONNECT Existing Constructions Cat6 WA LLSTAT IO N Place a Case with an iPad installed onto the WallStation to determine power was installed properly and the iPad charges. COMPLETE...
  • Page 27 CONNECT WA LLSTAT IO N Upgrading a LAUNCH WallStation to CONNECT PRO 1. Remove the old LAUNCH WallStation from the wall making sure to keep the existing anchors installed into the wall.
  • Page 28 CONNECT WA LLSTAT IO N Upgradeing LAUNCH WallStation Disconnect the two wires in the wall from the green phoenix connector...
  • Page 29 CONNECT Upgradeing LAUNCH WallStation WA LLSTAT IO N Connect the TE-Phoenix connector to the existing wire ran in the wall. Next connect the TE cable into the back of the white TE Connector on the WallStation DC Adapter. Zip tie the Connector to the DC board for added cable retnetion.
  • Page 30 CONNECT Upgradeing LAUNCH WallStation WA LLSTAT IO N Insert the CONNECT WallStation into the wall opening from the previous LAUNCH WallStation. IMPORTANT: Make Sure to position the WallStation with the Up Arrow facing up. Use a leveling tool to level the WallStation.
  • Page 31 CONNECT Upgradeing LAUNCH WallStation WA LLSTAT IO N Use the old screws or provided screws to attach the WallStation to the preinstalled anchors...
  • Page 32 CONNECT WA LLSTAT IO N Upgradeing LAUNCH WallStation Attach the WallStation Cover Plate over the WallStation making sure to alight the positioning notch with the tooth on the WallStation.
  • Page 33 CONNECT WA LLSTAT IO N Upgradeing LAUNCH WallStation Place a Case with an iPad installed onto the WallStation to determine power was installed properly and the iPad charges. COMPLETE...
  • Page 34 CONNECT WA LLSTAT IO N IPORT CONNECT Pro WallStation Install New Construction - 2 Wire Before Construction is complete 1. Determine the desired location of the IPORT Connect Pro WallStation will live when the construction is completed.
  • Page 35 CONNECT New Construction - 2 Wire WA LLSTAT IO N Install a 1 Gang electrical box or low voltage ring in the desired location of the WallStation. Electrical NOTE: The CONNECT PRO WallStation will cover a 1G electrical box only. A 2 Gang electrical box will interfere with the mounting hardware.
  • Page 36 CONNECT WA LLSTAT IO N New Construction - 2 Wire Run a 14AWG 2 wire cable from the WallStation location to a nearby AC outlet, closet, or network rack location. NOTE: Make sure to secure the 2 Wire cable appropriately onto the Electrical box or Low Volt- age ring to retrieve at a later time.
  • Page 37 CONNECT New Construction - 2 Wire WA LLSTAT IO N Installing the WallStation After Construction Locte the 1 gang boxed saved for the wallstation and locte the end of the 2 wire for power. Grommit not included...
  • Page 38 CONNECT New Construction - 2 Wire WA LLSTAT IO N Remove the WallSation, Drywall anchors and Screws from the box and place on a table.
  • Page 39 CONNECT New Construction - 2 Wire WA LLSTAT IO N Insert the WallStation into the 1G box. NOTE: the 1G box or Low voltage ring was used to save the space of the WallStation. The WallStation was designed to be use without the need for a junc- tion box.
  • Page 40 CONNECT New Construction - 2 Wire WA LLSTAT IO N 5. Use a leveling tool to level the WallStation and mark the 4 locations for the provided Anchors. Remove the WallStation from the 1G Box.
  • Page 41 CONNECT New Construction - 2 Wire WA LLSTAT IO N Remove the Wall Station and screw the provided anchors into the wall where marked.
  • Page 42 CONNECT New Construction - 2 Wire WA LLSTAT IO N Connect the Phoenix to TE cable provided to the 14-2 wire and onto the White TE Connector on the WallStation DC Adapter. Zip tie the Connector to the DC board for added cable retnetion.
  • Page 43 CONNECT WA LLSTAT IO N New Construction - 2 Wire Insert the WallStation back into the 1G box and use the provided screws to attach the WallStation to the wall. IMPORTANT: Make Sure to position the WallStation with the Up Arrow facing up.
  • Page 44 CONNECT New Construction - 2 Wire WA LLSTAT IO N Attach the WallStation Cover Plate over the WallStation making sure to alight the positioning notch with the tooth on the WallStation.
  • Page 45 CONNECT New Construction - 2 Wire WA LLSTAT IO N Connect the 2 wire to DC Connector at the other end of the 2 wire Cable. 10. Connect the Provided DC Power Adapter into the wall and connect the barrel connector to the other end of the Phoenix adapter.
  • Page 46 CONNECT WA LLSTAT IO N For a clean finished look place the Connector and DC barrel plug back throug the grommit into the wall. Grommit not included...
  • Page 47 CONNECT New Construction - 2 Wire WA LLSTAT IO N Place a Case with an iPad installed onto the WallStation to determine power was installed properly and the iPad charges. COMPLETE...
  • Page 48 WA LLSTAT IO N WallStation Install Manual - Existing Construction - 2 Wire Determine the desired location of the IPORT Connect Pro WallStation. Use a 2-3/4” (70mm) hole saw to cut a hole in the desired location of the WallStation...
  • Page 49 CONNECT Existing Construction - 2 Wire WA LLSTAT IO N Insert the WallStation into the 2 3/4 - inch hole and use a leveling tool to level the WallStation. Mark the 4 locations for the provided Anchors. Remove the WallStation form the wall once you have marked the 4 anchor locations.
  • Page 50 CONNECT Existing Construction - 2 Wire WA LLSTAT IO N Screw the provided anchors into the wall where marked.
  • Page 51 CONNECT Existing Construction - 2 Wire WA LLSTAT IO N Use the 2 3/4 - inch hole to fish a 14/2 cable to a nearby AC outlet, closet or network rack.
  • Page 52 CONNECT Existing Construction - 2 Wire WA LLSTAT IO N Connect the Phoenix to TE cable provided to the 14-2 wire and onto the White TE Connector on the WallStation DC Adapter. Zip tie the Connector to the DC board for added cable retnetion.
  • Page 53 CONNECT Existing Construction - 2 Wire WA LLSTAT IO N Insert the WallStation back into the wall and use the provided screws to attach the WallStation to the wall anchores. IMPORTANT: Make Sure to position the WallStation with the Up Arrow facing up.
  • Page 54 CONNECT WA LLSTAT IO N Existing Construction - 2 Wire Attach the WallStation Cover Plate over the WallStation making sure to alight the positioning notch with the tooth on the WallStation.
  • Page 55 CONNECT WA LLSTAT IO N Existing Construction - 2 Wire 10. Connect the 2 wire to DC Connector at the other end of the 2 wire Cable. 11. Connect the Provided DC Power Adapter into the wall and connect the barrel connector to the other end of the Phoenix adapter.
  • Page 56 CONNECT WA LLSTAT IO N For a clean finished look place the Connector and DC barrel plug back throug the grommit into the wall. Grommit not included...
  • Page 57 CONNECT Existing Construction - 2 Wire WA LLSTAT IO N Place a Case with an iPad installed onto the WallStation to determine power was installed properly and the iPad charges. COMPLETE...

This manual is also suitable for:

Connect pro 72351