Subscribe to Our Youtube Channel
Summary of Contents for VideoComm Technologies EV-L1R2409D1
- Page 1 It’s About Real-Time Wireless Elevator Video System EV-L1R2409D1 OWNER’S MANUAL VideoComm Technologies (888) 379-2666 US Toll Free (905) 336-9665 Phone (905) 336-9662 Fax www.VideoTransmitters.com...
-
Page 2: Table Of Contents
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Table of Contents SAFETY NOTICES.……………………………………………………………………………………………………..3 INTRODUCTION……..…………………………………………………………………………………………………..4 Advantages..….………………..…..……………………………………………….……………...4 PRE INSTALLATION…………………………………………………………………………………...……………….5 Site Evaluation….………………..…..……………………………………………….……………...5 Tools Required…….………..……….……………………………..……………………………...…6 Camera Parts List………..…………..…………………………………………………………….…7 Parts List………………………………………………………….…………………………..………8 Preparing Camera for Installation…...……………………………………………………………..9 CORNER-MOUNT CAMERA INSTALLATION………………………………...………………………………….10 Corner-Mount Camera Installation….……………………………………………………………..11 ADJUSTING CAMERA FOCUS & TILT…...………………………………………………………………………...12 SECURING CAMERA FACEPLATE……….……………………………………………………………………...…13... -
Page 3: Safety Notices
The system has been certified by the FCC for use with other products without any further certification (as per FCC section 2.1091). Warning: Changes or modifications not expressly approved by VideoComm Technologies could void the user’s authority to operate the equipment... -
Page 4: Introduction
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Introduction The All New 2.4GHz FHSS, Wireless Elevator Video System delivers D1 Quality (720 x 480) encrypted digital video up to 200 Floors. Featuring a pre-configured plug & play design and a vandal-proof corner mount 480 line CCD Camera, this system is the most economical elevator surveillance solution. -
Page 5: Pre Installation
This will determine where you will mount the transmitter (roof or under-carriage of elevator cab) and the receiver (mechanical penthouse or elevator pit). Every elevator installation is unique – These guidelines may or may not apply to your particular application. For additional application design assistance contact VideoComm Technologies Customer Service VideoComm Technologies Customer Service... -
Page 6: Tools Required
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Tools Required The Wireless Elevator Camera System is designed to be “Plug & Play” and simple to install with minimal tools. The following is a list of recommended tools to setup your system. -
Page 7: Camera Parts List
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Camera Parts List... -
Page 8: Parts List
Please inspect the packaging carefully to ensure you have received all the necessary parts and accessories listed. Refer to the following chart to determine which parts are included with your product. If any parts are missing or damaged, contact VideoComm Technologies, Customer Service or your re-seller immediately. PARTS... -
Page 9: Preparing Camera For Installation
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Preparing Camera for Installation Use the security key to remove three security screws on the camera faceplate. Remove the camera faceplate from camera and mounting bracket. Use the security key to remove four security screws from the camera’s protective dome. -
Page 10: Corner-Mount Camera Installation
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Using a Phillips screwdriver, remove the four screws from the camera base plate (Figure A) and remove base plate from the triangular mounting bracket (Figure Figure A Figure B Corner-Mount Camera Installation Place mounting bracket in the corner flush with the desired location. -
Page 11: Corner-Mount Camera Installation
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Secure mounting bracket to the wall. From the rooftop of the elevator, connect the 12VDC power supply to a 115 Volt electrical outlet. Feed the power barrel jack and 18” of video cable into the cab through the ½”... -
Page 12: Adjusting Camera Focus & Tilt
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Adjusting Camera Focus & Tilt To adjust the camera tilt use a Phillips screwdriver. Loosen the two lock-tight screws on both sides of the support bracket. Adjust tilt up / down and re-tighten to set. -
Page 13: Securing Camera Faceplate
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Securing Vandal-Proof Enclosure Place the black camera shroud around the lens to conceal the camera’s components Attach the protective dome enclosure to the camera base plate using four security screws Connect the video output jack to the 25’ video cable previously fed through the roof. -
Page 14: Securing Power & Video Cables To Cab
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Securing Power & Video Cable to Exterior Cab Warning!!! The video cable must be clear of any moving mechanisms including but not limited to: Traveling cable, counter-weight, cabling trough, guide rails, brakes, door mechanics, sensors and safety devices. -
Page 15: Opening & Closing The All Weather Enclosure
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Opening & Closing the All Weather Enclosure To make video and power connections we must access the interior of the enclosure by removing the front cover. The front cover can be removed two ways:... -
Page 16: Mounting The Transmitter
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Mounting the Transmitter Warning: Not all elevator cabs are the same. The following is for illustration purposes only. Consult with the elevator manufacturer for detailed information pertaining to the layout and construction of the elevator undercarriage, shaft and ideal Tx & Rx mounting locations. -
Page 17: Installation Application Diagrams
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A SINGLE ELEVATOR SHAFT APPLICATION DIAGRAM MULTIPLE ELEVATOR SHAFTS APPLICATION DIAGRAM... -
Page 18: Video & Audio Cable Termination
Loosen the desired cable gland. Feed the video and audio coax cable starting from the outside of the IP-67 enclosure through the cable gland hole. VideoComm Technologies recommends the use of RG-59 or higher grade coaxial cable for video and audio terminations. At this time, attach your BNC-Male connector to your Coax Cable and terminate inside. -
Page 19: Power Supply Connection
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A POWER SUPPLY CONNECTION WARNING! Unplug power supply before connecting raw leads to power input terminal. An electrical short can occur, causing harmful damage to the unit. Each unit is Polarity Protected. Turn the small cable gland counter clock wise Feed the power cable wire through the cable gland. -
Page 20: Mounting The Receiver
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Mounting the Receiver Warning!!! The receiver must be clear of any moving mechanisms including but not limited to: traveling cable, counter-weight, cabling trough, guide rails, brakes, door mechanics, sensors and safety devices. To ensure compliance with the safety standards and laws in your Country, State or City, consult with your local Elevator authority for guidelines pertaining to mounting a device in an elevator shaft prior to installation. -
Page 21: Warranty Information & Returns
EV-L1R2409D1 WIRELESS ELEVATOR CAMERA SYSTEM REV. A Warranty Information / Terms & Conditions VideoComm Technologies, herein referred to as “VCT.” LIMITED WARRANTY VCT hereby warrants, subject to the conditions here in below, that should this product become defective by reason of improper workmanship or material defect during the specified warranty period, VCT will repair the same, affecting all necessary parts without charge for either parts or labor, or replace the unit at VCT option. - Page 22 FLOORS CAPABLE RESOLUTION EV-L1R2409D1 - 2.4GHz FHSS D1-Type Wireless Elevator Video System - Range up to 200 Floors The All New 2.4GHz FHSS, Wireless Elevator Video System delivers D1 Quality (720 x 480) encrypted digital video up to 200 Floors. Featuring a pre-configured plug & play design and a vandal-proof corner mount 480 line CCD Camera, this system is the most economical elevator surveillance solution.
- Page 23 Wireless Elevator Video System EV-L1R2409D1 Corner Mount Vandal-Proof Camera Advantages Crystal clear video from 480 line resolution SuperHAD SONY CCD Unique vandal-proof modern corner mount design View every corner in elevator cab with the ultra wide-angle 2.8mm board lens Power supply and 25’ video cable included for convenient...
- Page 24 Wireless Elevator Video System EV-L1R2409D1 Transmitter & Receiver OPERATING FREQUENCY 2.4GHz - 2.48GHz Digital Frequency Hopping Spread Spectrum FREQUENCY CONTROL Automatic Channel Selection MODULATION FORMAT FHSS (16 QAM, QPSK, BPSK) SECURITY AUTHENTICATION Automatic Rolling Encrypted Authentication System DATA RATE Up to 12Mbps...
- Page 25 Wireless Elevator Video System EV-L1R2409D1 WhAT PEoPlE ARE SAying Kit includes ALL WEATHER TRANSMITTER ALL WEATHER RECEIVER CORNER MOUNT VANDEL-PROOF CAMERA 25’ POWER / VIDEO CABLE TWO X 3dB RUBBER DUCk ANTENNA THREE 12 VDC POWER SUPPLIES TWO UNIVERSAL MOUNTING BRACkETS ONE REMOTE CONTROL OWNER’S MANUAL...
Need help?
Do you have a question about the EV-L1R2409D1 and is the answer not in the manual?
Questions and answers