Table of Contents
Advertisement
Quick Links
34 DEGREE ANGLED AIR STRIP NAILER
CT3320
INSTRUCTION MANUAL
IMPORTANT:
These instructions accompanying the product are the original instructions. This
document is part of the product, keep it for the life of the product passing it on to
any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
Cannon Tools Limited
Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
Advertisement
Table of Contents
Related Manuals for Neilsen CT3320
Summary of Contents for Neilsen CT3320
- Page 1 34 DEGREE ANGLED AIR STRIP NAILER CT3320 INSTRUCTION MANUAL IMPORTANT: These instructions accompanying the product are the original instructions. This document is part of the product, keep it for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before assembling, operating or maintaining this product.
-
Page 3: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: 34 DEGREE ANGLED AIR STRIP NAILER Model: CT3320 Applicable EC Directives: EC Machinery Directive 2006/42/EC Harmonized standards EN ISO 11148-13:2018 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. -
Page 4: Specification
1. SPECIFICATION Air pressure: 5-8 Bar Air inlet: 1/4" Nail type: 50-90mm long, 2.87-3.8mm diameter, 34o clipped head nails Magazine capacity: 80pcs Warning: Wear approved safety glasses and ear defenders. 2. IMPORTANT SAFETY INFORMATION a). Read the instruction manual fully. Do not attempt any operation until you have read and understood this manual. -
Page 5: Technical Description
3. TECHNICAL DESCRIPTION... -
Page 6: Functional Diagram
4. FUNCTIONAL DIAGRAM Air tools are cycled by a compressed air operated single piston design, the following illustrations show the four functional cycles that occur when the tool is operated to drive a fastener. FIG.1 AT REST FIG.2 DRIVING STROKE RESERVOIR OF HIGH PRESSURE AIR FIG.3 END OF STROKE TRIGGER STILL PULLED FIG.4 RETURNING... -
Page 7: Unpacking And Checking
5. UNPACKING AND CHECKING Carefully remove the product from the packaging and examine it for any sign of damage that may have happened during shipping. Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the seller and do not attempt to use the air nailer. -
Page 8: Air Supply
6. AIR SUPPLY Air Supply To prevent explosion: Use only clean, dry, regulated, compressed air to power this tool. Do not use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool. (1) Use dry compressed air filtered oil and water. (2) The compressed air pressure can not exceed to 8bar. - Page 9 7. USING THE TOOL 7.1 POWER SOURCE This tool applies to normal air compressor and is designed to operate in clean, dry and compressed air at regulate pressures between 5~8bar. Place two or three drops of air tool oil into the tool’s air inlet at the beginning of workday and try it twice or three times.
- Page 10 b. Detach the air supply. c. change the Mode Switch to setting. d. Disengage the pusher by pulling it back slightly to disengage fastener strip, press and hold pusher Lever, and slide pusher to front of Magazine. e. Empty the Magazine. f.
-
Page 11: Lubrication And Maintenance
8. LUBRICATION AND MAINTENANCE 8.1. Disconnect the air supply from the tool before lubricating. 8.2. Your tool requires lubrication before you use it for the first time. 8.3. Wipe off excessive oil at the exhaust. Excessive oil will damage o-rings of tools. -
Page 12: Explanation Of Symbols
10. EXPLANATION OF SYMBOLS WARINING! In accordance with essential safety standards of applicable European directives First read the instruction manual. Wear safety glasses and ear protection. -
Page 13: Exploded View
11. EXPLODED VIEW... - Page 16 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...