Advertisement
Secure Surface-Mounting
1.
Use a flat-head screwdriver to remove the rubber feet.
Note that two of the surface mounting holes are located beneath the two rear
rubber feet (FIG. 6).
Surface Mounting holes
The Strain Relief Bracket
(mounted inside the enclosure)
also uses this mounting hole
FIG. 6
BOTTOM PANEL (BOTTOM VIEW)
2.
Use a flat-head screwdriver to remove the Cable Knockout from the bottom panel.
3.
Position the TTS enclosure in the desired installation location.
4.
Use the two rear mounting holes to secure the TTS enclosure to the mounting
surface.
5.
Run all device cable(s) through the Cable Knockout.
6.
Install the Cable Strain Relief (FIG. 2) on the cable(s).
7.
Install the cable with Cable Strain Relief into the Strain Relief Bracket.
8.
Install the Strain Relief Bracket inside the enclosure.
The mounting screw that secures the Strain Relief Bracket to the TTS Enclosure
passes through the Strain Relief Bracket and serves as the third mounting screw,
completely securing the TTS enclosure to the surface.
9.
Connect device cabling to the Touch Panel, Keypad(s) or ControlPad, depending
on the type of TTS installed.
Note: Refer to the Operation/Reference Guide for the device being installed for
cabling and connection details.
10.
Install the Panel, Keypad(s) or ControlPad as described in the TTS Installation
Guides.
Detailed Dimensions of TTS Enclosures
The following illustrations provide detailed dimensions for the TTS enclosures:
NXA-TTS43X-BL and NXA-TTS500-BL
The NXA-TTS43X-BL and NXA-TTS500-BL share the same TTS enclosure (FIG. 7):
MET-TTS1/2/3-BL and AP-TTS16-BL
The MET-TTS1/2/3-BL and AP-TTS16-BL share the same TTS enclosure (FIG. 5):
Additional Documentation
Refer to the Installation Guide specific to the TTS Table-Top Stand that you are
installing for detailed instructions on installing the Touch Panel, Keypad(s) or
ControlPad into the TTS Enclosure:
•
AP-TTS16-BL Installation Guide
•
MET-TTS123-BL Installation Guide
•
NXA-TTS43X-BL Installation Guide
•
NXA-TTS500-BL Installation Guide
© 2015 Harman. All rights reserved. Metreau, AMX, AV FOR AN IT WORLD, HARMAN, and their respective logos are registered trademarks of
HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective companies.
AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.
The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153
AMX (UK) LTD, AMX by HARMAN - Unit C, Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/
Last Revised: 11/05/2015
(front)
Surface Mounting holes are
hidden beneath the rear pair
of rubber feet
Cable knockout
(rear)
FIG. 7
ENCLOSURE DIMENSIONS - NXA-TTS43X-BL AND NXA-TTS500-BL
FIG. 8
ENCLOSURE DIMENSIONS - MET-TTS123-BL AND AP-TTS16-BL
93-2261-10
REV: B
Advertisement
