Related Manuals for Sam 6 TONNE SINGLE AXLE
Summary of Contents for Sam 6 TONNE SINGLE AXLE
- Page 1 INSTRUCTION AND PARTS MANUAL Strong. Simple. Smart. 3.8, 5 AND 6 TONNE COMBO SPREADERS 800mm wide floor-belt All models from 2015 6 TONNE SINGLE AXLE (AUS) 3.8 TONNE SINGLE AXLE (AUS) www.samfarmmachinery.com...
-
Page 2: Model Details
MODELS This Instruction and Parts Manual covers all Australian 3.8, 5 and 6 Tonne SAM Combo Spreaders fitted with an 800mm floor-belt manufactured since 2015. For all other SAM Machinery Instruction Manuals please visit www.samfarmmachinery.com SERIAL NUMBER All SAM Machinery products are identified with a unique serial number located on the front of the machine (e.g. -
Page 3: Quality Guarantee
QUALITY GUARANTEE SAM Machinery products are guaranteed against any defects in either material or manufacture for a period of 24 months from delivery date provided that the equipment has not been subject to abuse or misuse, operated incorrectly, over loaded or used for purposes other than for which the equipment is designed or is not maintained correctly or if fitted with other than genuine parts. -
Page 4: Basic Safety
Carry out any pre-use checks as specified in the operator’s manual. HEALTH & SAFETY RISK ASSESSMENT A hazard identification, assessment and control procedure has been conducted on a representative SAM Fertiliser Spreader and where necessary appropriate risk control measures have been outlined below;... -
Page 5: Basic Maintenance
BASIC MAINTENANCE To keep your SAM Spreader in excellent working condition, please follow these basic maintenance procedures as you go. Keep your machine fairly clean and very well greased. Before each use; check the hydraulic system for signs of oil leaks or wear. Check there is no play in the spinner bearings by lifting up on the spinner discs. - Page 6 The SAM Combo Spreader has one ground drive speed. HYDRAULICS Standard SAM Fertiliser Spreaders are fitted with two OMP50 hydraulic motors running in series, requiring an external oil flow of 50 litres/minute. It is very important that you adjust the hydraulic oil flow from the tractor back to 50 litres/minute if possible (or 70 litres/minute maximum).
- Page 7 SET-UP AND OPERATION - PLEASE READ flows over 70 litres/minute. Note, the higher the bypass oil flow, the higher the pressure in the Fertiliser Spreader’s hydraulic system. COUPLING THE HYDRAULICS The live hose (red) must be coupled to a high pressure outlet point on the tractors external hydraulic system. This take off point can be fitted to an existing double acting valve already fitted for farm machinery, or a new fitting can be installed.
- Page 8 PARTS MANUAL - SAM 3.8T, 5T & 6T COMBO SPREADER MACHINE SIDE-VIEW REFERENCE PART NUMBER DESCRIPTION QTY. 3103 Wheel & Tyre - 11.5/80 x 15.3 (12ply) 3107 Wheel & Tyre - 400/60 X 15.5 (TR Tread) 3948 Wheel & Tyre - 550/60 x 22.5 (16ply) P250 Chain &...
-
Page 9: Parts Manual
PARTS MANUAL MACHINE REAR-VIEW - SPINNER SET-UP REFERENCE PART NUMBER DESCRIPTION QTY. Danfoss OMP32/8 Hydraulic Motor P4751 P3040 Skirt Pressing (S/S) - (inc. Rubber + Rivets) - Left/Right P4686 Skirt Rubber & Rivet Set - x2 (2.77 x 80mm) + 34 Rivets P3067 Floor-belt and Chain (Complete) Spinner Tube Mounting Frame... - Page 10 PARTS MANUAL GROUND DRIVE REFERENCE PART NUMBER DESCRIPTION QTY. P4704 3/4” Stainless Steel Ram Pin & S10 R Clip 4282 Clutch RAM - 2.5” D/A - 5 and 6T Combo 4011 & 4012 Bolt 3/4”x5”UNC & Nyloc Nut 3/4”UNC P0424 Chain 16B (1”...
- Page 11 COMMON BEARING SIZES AND DIMENSIONS BEARING SIZES BY HUB MAKE / MODEL HUB MAKE / MODEL HUB SIZE BEARINGS SEAL HUB CAP ADR Mk2 60sq 30211 / 30208 100 x 57 x10 Mk2 80mm ADR Mk3 60sq 30211 / 30208 100 x 56 x 10 Mk3 80mm ADR Mk3...
-
Page 12: Troubleshooting
TROUBLESHOOTING If you are experiencing a problem or have a question that is not listed in the chart below, please contact your local dealer directly. QUESTION / PROBLEM SOLUTION 3.8t Fertiliser Spreader = 3m3 of fertiliser 3.6t of Superphosphate (1.2t/m3 density) 4.8t of Lime (1.7t/m3 density) 2.3t of Urea (0.8t/m3 density) 5t Fertiliser Spreader = 4.25m3 of fertiliser... - Page 13 TROUBLESHOOTING QUESTION / PROBLEM SOLUTION Standard SAM Fertiliser Spreaders are fitted with two OMP50 What hydraulic oil flow is required? hydraulic motors running in series, requiring an external oil flow of 50 litres/minute. The spinner shaft should turn at approx. 850RPM at What RPM should the spinner shaft turn at? 50 litres/minute at 2000psi.
- Page 14 SPREADING TABLES SPREADING TABLES...
- Page 15 SPREADING TABLES The spreading table below is fixed beside the back door of each SAM Fertiliser Spreader. The required fertiliser application rate can be set by adjusting the back door jack and viewing the spreading table sticker to achieve the desired rate per hectare - setting the top of the back door level with the selected box.