Sarabec chimeflash User Manual

Op onal Accessories
A Telephone alert transmi er is available which can plug
into a BT phone socket, every me the phone rings the
flash
chime will alert you.
Programming of this accessory is the same as the Doorbell
Push (outlined on the previous page).
flash can also be powered by a 12v Mains power
The chime
supply, when using the system in this way the ba eries in
the receiver act as a ba ery back up in case of power failure.
The plug fits into a socket in the back of the receiver and you
feed the wire along the retaining channel.
Only the 12v 1A Sarabec power supply should be used with
this equipment.
Troubleshoo ng
Problem
The RED Indicator on the receiver is blinking every 15
seconds and volume level has dropped
The Green or Orange Symbols on the receiver are blinking
every 15 seconds
I need to clear a transmi er from the systems memory
My system is being triggered at random (Possibly by a
neighbour's doorbell system)
I cannot remove my transmi er from its moun ng plate
If you have a Pacemaker or ICD fi ed you may wish to read the FAQ on our website before using this product.
Sarabec Ltd
Sarabec Ltd declares that chime
15 High Force Road
complies with all relevant UK Statutory
Middlesbrough
Instruments.
United Kingdom
TS2 1RH
Sarabec Ltd declares that chime
Telephone: 01642 247789
complies with all relevant EU direc ves.
email: mail@sarabec.co.uk
Sarabec's EU authorised representa ve:
website: www.sarabec.com
HUMANTECHNIK GmbH, Im Wörth 25,
D‐79576 Weil am Rhein , Germany.
This system carries a 2 year
guarantee, please contact your
The full declara on of conformity for
point of sale in the event of
the Chimeflash is available from Sarabec
any issues.
The Wheely bin logo is the industry wide symbol for this
type of product. The symbol, when appearing on electronic
product, indicates that the item should NOT be treated as
ordinary household waste when due for disposal.
Solu on
Replace ba eries as they are LOW (replace with "C" size
Alkaline ba eries)
Replace the corresponding transmi er coin cell ba ery
(CR2032)
Enter the setup mode, then press and hold the setup
bu on for 3 seconds, a beep will be heard, press the setup
bu on once and clear the second symbol if required by
holding the setup bu on again for 3 seconds, if not press
the setup bu on again to leave the setup mode
Open the ba ery cover of the transmi er, remove the
ba ery, press and hold the pushbu on for 5 seconds whilst
inser ng the ba ery back into the push, the LED will blink 5
mes to show that a new code has been generated.
Clear the transmi er from the memory of the receiver and
follow the setup instruc ons to re‐pair the transmi er to
the receiver again.
There is a small tab located on the bo om of the moun ng
plate which must be pushed away from the transmi er,
this will allow you to rotate the transmi er on the plate to
remove it
flash
Specifica ons
Frequency: 868.4MHz
Maximum Volume: Up to 100dB @ 1m
flash
Range: Up to 300m (Open Space)
Power Requirements 3 x C size Alkaline ba eries or
Mains Power 12v 1A PSU for
Receiver
1 x CR2032 for Transmi ers
Is a registered mark of Sarabec Ltd.
RoHS
Sarabec Ltd
Chime Flash Issue 1 May 2021
Introduc on
The Sarabec flash provides a prac cal wireless solu on for hearing and seeing when you have a caller at the door or
chime
when the telephone is ringing. (Telephone transmi er sold separately)
This is achieved by using extra loud sounds, ultra‐bright flashing LED's, and colored indicators
System contents

flash
Receiver
chime

Bellpush (With Moun ng Plate)

CR2032 Size Ba ery (For Bellpush)

3 x "C" size Alkaline Ba eries (For Receiver)

Screws and Fixings

Opera ng Instruc ons
chime flash
User Manual
.