Table of Contents
Advertisement
Quick Links
Operating Instructions and Parts Manual
Please read and save these instructions. Read through this owner's manual carefully before using product. Protect yourself
and others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in
personal injury and/or damage to product or property. Please retain instructions for future reference.
FOR CUSTOMER SERVICE
Technical Question?
CALL 1-866-458-2472
customerservice@oem-tools.com
UNPACKING
After unpacking unit, inspect carefully for any damage
that may have occurred during transit. Check for loose,
missing, or damaged parts. If any damage is observed,
a shipping damage claim must be filed with carrier. Do
not use the OEMTOOLS™ Cam Phaser Kit if broken,
bent, cracked or damaged parts (including labels) are
noted. Any Cam Phaser Kit that appears damaged in
any way, operates abnormally or is missing parts should
be removed from service immediately. If you suspect
that the Cam Phaser Kit was subjected to shock load
(a load that was dropped suddenly, unexpectedly, etc.)
immediately discontinue use until it has been checked
by a factory authorized service center.
WARNING
The following safety information is provided as a guideline to help you operate your Cam Phaser under the safest possible conditions. Any tool or
piece of equipment can be potentially dangerous to use when safety or safe handling instructions are not known or not followed. The following
safety instructions are to provide the user with the information necessary for safe use and operation. Please read and retain these instructions for
the continued safe use of your service system. Failure to follow instructions listed below may result in serious injury. In addition, make certain that
anyone who uses the equipment understands and follows these safety instructions as well.
EXPLANATION OF SAFETY SIGNAL WORDS
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may
result in property damage.
NOTES: Provide clarity and helpful information.
Thank you very much for choosing an OEMTOOLS™ Product!
For future reference, please register your new tool at www.oem-tools.com and complete the owner's record below:
Model: _______________ Purchase Date: ___________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product
before you begin using it. This product is designed for certain applications only. OEMTOOLS™ cannot be responsible for issues arising
from modification. We strongly recommend this product is not modified and/or used for any application other than that for which it was
designed. If you have any questions relative to a particular application, DO NOT use the product until you have first contacted customer
service to determine if it can or should be performed on the product.
3/17
2017 OEMTOOLS™
1
CAM PHASER KIT
24209
Advertisement
Table of Contents
Summary of Contents for OEM Tools 24209
- Page 1 Operating Instructions and Parts Manual 24209 Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal injury and/or damage to product or property.
-
Page 2: Important Safety Instructions
Operating Instructions and Parts Manual 24209 CAM PHASER KIT IMPORTANT INSTRUCTIONS PURPOSE A common problem for Ford vehicles with the 4.6 or 5.4 3V engine is AND SAFETY RULES a metallic knocking noise as a result of cam phaser failure. Installing 1. - Page 3 Operating Instructions and Parts Manual 24209 CAM PHASER KIT Lockout correctly installed 14. Once you have rotated the cover out of the way, you can see the vanes that control the cam phaser movement. The voids next to these vanes is where the Lockout will be installed. Because there are 5 locations and only one Lockout, you will need to determine which location the Lockout is to be installed.
-
Page 4: Section 1: Programming Instructions
Operating Instructions and Parts Manual 24209 CAM PHASER KIT SECTION 1: PROGRAMMING INSTRUCTIONS DTCs (All Vehicles): Set the parking brake. Connect one (1) end of the provided cable to the This option checks for Diagnostic Trouble Codes (DTCs). programmer. Locate the diagnostic port under the driver’s side of the dash. Plug the programmer cable into the diagnostic port. - Page 5 Operating Instructions and Parts Manual 24209 CAM PHASER KIT The programmer will display 3 tuning options: Gas Vehicles: PRESET TUNE- Select a previously saved tune for installation. Use the buttons to the right of the screen to highlight the tune for the octane fuel being used.
-
Page 6: Shift Points
Operating Instructions and Parts Manual 24209 CAM PHASER KIT Use the buttons to the right of the screen to scroll up or down, and than what was installed from the factory. For more information, see highlight the desired MPH. Press ‘Select’ to save the chosen value. - Page 7 Operating Instructions and Parts Manual 24209 CAM PHASER KIT To adjust the shift points in all gears the same, select ALL from the Shift Press the ‘Back’ button to go back to the Gear Shift menu. Repeat the Points menu.
- Page 8 Operating Instructions and Parts Manual 24209 CAM PHASER KIT PER GEAR SHIFT FIRMNESS: Use the buttons to the right of the screen to For more information on the Cold Air Intake option, see Programming scroll up or down, and highlight the gear change to adjust.
- Page 9 Operating Instructions and Parts Manual 24209 CAM PHASER KIT REVIEW CHANGES IMPORTANT NOTE: The next screen displays all of the Tuning Options for your vehicle, and the While the unit is programming, the following is EXTREMELY IMPORTANT: options selected. Use the buttons to the right of the screen to scroll up or DO NOT leave the vehicle while programming is in process.
- Page 10 Operating Instructions and Parts Manual 24209 CAM PHASER KIT If the vehicle has no DTCs, the programmer will proceed immediately to After the programmer has successfully programmed the vehicle, follow Reading Vehicle mode. the instructions on the screen until you see the Successful screen.
- Page 11 Operating Instructions and Parts Manual 24209 CAM PHASER KIT TPMS ADJUST (Most Vehicles) If the vehicle has any DTCs, the programmer will display all DTCs, and the total number of DTCs reported from the vehicle’s computer. To clear all This feature allows instant adjustment of the minimum pressure for tire DTCs, press the ‘Clear’...
-
Page 12: Device Info
Operating Instructions and Parts Manual 24209 CAM PHASER KIT DEVICE INFO Select ‘Setgs’ to view the current options that are programmed in the vehicle. Select ‘Back’ button to return to the previous menu. Use the buttons to the right of the screen to highlight Device Info. Press the ‘Select’... -
Page 13: Section 2: Programming Vehicle Back To Stock, Changing Tuning Options, And Selecting Preset Tunes
Operating Instructions and Parts Manual 24209 CAM PHASER KIT The Tuning Menu will display a pound sign “#” next to the options that were selected for the previous programming session. To make changes, follow the Tuning instructions from Section 1. -
Page 14: Section 3: Technical Information & Troubleshooting
Operating Instructions and Parts Manual 24209 CAM PHASER KIT SECTION 3: TECHNICAL INFORMATION & TROUBLESHOOTING ATTEMPTING TO PROGRAM A DIFFERENT VEHICLE 3-1: What to Do Before Taking the Vehicle in For Service Code 0125: VIN Mismatch will appear if attempting to program the computer in another vehicle without first programming the last vehicle Return Vehicle to the Stock Programming. - Page 15 Operating Instructions and Parts Manual 24209 CAM PHASER KIT AFTERMARKET PARTS (Gas) adjust the height up or down as needed to dial in the exact calibration. Another method of measuring the tire diameter: The tuning provided in your programmer works well with popular bolt-on aftermarket parts.
-
Page 16: Section 4: Updating Your Programmer
Operating Instructions and Parts Manual 24209 CAM PHASER KIT SECTION 4: UPDATING YOUR PROGRAMMER 3. Open the Tuner Update Application software from the PC. Once the update software is installed, there will be a shortcut installed on The programmer may need to be updated if support for the vehicle was your desktop.