Advertisement
Quick Links
MANURE SPREADER
MODEL MX25
ASSEMBLY INSTRUCTION MANUAL
Please review and understand the
operators manual before attempting
to operate this machinery.
EMB MANUFACTURING INC.
4144 BOOMER LINE
ST. CLEMENTS, ON
N0B 2M0 CANADA
PH: (519) 699-9283
FAX: (519) 699-4146
PRINTED IN CANADA
Rev 260213
PART NUMBER: Z97520
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for EMB WALLENSTEIN MX25
- Page 1 MANURE SPREADER MODEL MX25 ASSEMBLY INSTRUCTION MANUAL Please review and understand the operators manual before attempting to operate this machinery. EMB MANUFACTURING INC. 4144 BOOMER LINE ST. CLEMENTS, ON N0B 2M0 CANADA PH: (519) 699-9283 FAX: (519) 699-4146 PRINTED IN CANADA...
-
Page 2: Assembly Safety
ASSEMBLY SAFETY 1. Read and understand the Assembly Manual and all safety signs before starting. 2. Follow good safety practices: Keep service area clean and dry. Be sure electrical outlets and tools are properly grounded. Use adequate light for the job at hand. 3. - Page 3 ASSEMBLY This assembly manual is for all trailer model manure spreaders. The MX25G is used as an example but generally applies to all manure spreader models. Model specific instruc - tions are identified in the manual. The machine is shipped from the factory in a partially disassembled configuration and attached to a pallet that provides easy moving and handling. Always use tools, equip- ment and fork lifts of appropriate size and capacity for the job. Inspect for damage from shipping, immediately contact the shipping company if damage is found.
- Page 4 Uncrating the Spreader 1. Remove all screws securing upper part of crate to lower skid. There are two (2) screws located at each of four corners around bottom of crate, and one in center of both sides. Photo 1 Photo 1 2.
- Page 5 3. Locate Ground Drive Axle Assembly, Engagement Handle and Tires shipped in bed of spreader. Photo 3 Photo 3 Axle/Tires/Engagement Handle 4. Unfasten and remove Engagement Handle Assembly secured inside spreader bed. Photo 4 Photo 4...
- Page 6 5. Remove the Hex Bolt 1/4NC x 1-1/2 & Hex Lock Nut 1/4NC temporarily mounted at the Drive Engagement Connection Rod (for your convenience). Inset A, Photo 5). Use this hardware to mount and secure the Engagement Handle Assembly. Photo 6 Photo 5 Photo 6...
- Page 7 6. Using a lift truck, raise the spreader from the lower skid and place on a set of four jacks. Position jacks at a workable height for axle and tire installment. Exercise extreme caution when raising spreader to ensure a safe working environ- ment.
- Page 8 7. Locate Trailer Hitch/Tongue & Cross Bar mounted to top of shipping crate and re- move. Photo 9 Photo 9 8. Remove two (2) Carriage Bolt 5/16NC x 3/4 & two (2) Flange Nut 5/16NC from both left and right hand Box Sides at rear of spreader. Photo 10 Photo 10...
- Page 9 9. Attach the cross bar at rear of spreader with hardware removed in Step 8. Photo 11 Photo 11 10. Remove two (2) Hex Bolt, 1/2NC x 2-3/4 & two (2) Hex Lock Nut 1/2NC from left and right Main Frame at front of spreader. Photo 12 Photo 12...
- Page 10 11. Slide the Hitch Frame into Main Frame at front of spreader and secure with the hard- ware removed in step 10. Photo 13 Photo 13 12. Install Ground Drive Axle Assembly over top of apron chain while holding # 50 Drive Chain above axle.
- Page 11 13. Loosely attach axle bearing pillow blocks at right side of spreader using two (2) Hex Bolt 5/8NC x 1-3/4 & two (2) Hex Lock Nut 5/8NC. Photo 15 Photo 15 14. Loosely attach Drive Sprocket side of axle bearing pillow blocks to spreader (left hand side).
- Page 12 15. Ensure Main Ground Drive Sprocket is aligned with #50 Roller Chain above. Photo 17. This alignment is generally set at factory but should be checked in case of misalignment during shipping. Photo 17 If alignment is out, loosen both Set Screw, 3/8NC and slide Ground Drive Sprocket as necessary.
- Page 13 16. Remove ten (10) Lug Nut 1/2NF from each axle hub and install two (2) Tires. Photo 19 & 20 Photo 19 "V" Tread faces towards rear of spreader. Tire shown below is LEFT hand side. Photo 20...
- Page 14 17. Installed Jack at upright position. Photo 21 Photo 21 18. Installed Jack at travelling position. Photo 22 Photo 22...
Need help?
Do you have a question about the WALLENSTEIN MX25 and is the answer not in the manual?
Questions and answers