Advertisement
Quick Links
Product Manual
•
Smart Thermostat HD Overview
o Smart Thermostat HD Hardware
Display
Thermostat
•
Installation Precautions
o Before installing the Smart Thermostat HD or servicing the HVAC equipment, turn off power
to the system.
o Leave power off until you have finished installing or servicing the HVAC equipment.
o Shorting the electric terminals at the control on the heating or cooling system is not
recommended. Do not test the system this way.
o When testing the existing system or the new Smart Thermostat HD do not run the cooling
system when it is cold outside as this may harm the compressor. Please wait for mild
temperature to test the cooling system.
o You must follow all local codes and ordinances for wiring the system.
o This Smart Thermostat HD should only be powered by a listed Class 2 power supply at 24
VAC (C-Wire or wall transformer).
o An amperage higher than 1 amp to each thermostat terminal may cause damage to the
thermostat.
o Verify that the system is 24 VAC. If the old system is labeled as 120 or 240 volts or has wire
nuts, the system is high voltage. Do NOT install this thermostat on a high voltage system.
Contact a local HVAC professional for help.
o Questions?
Visit: www.alarm.com/supportcenter or contact your service provider.
Smart Thermostat HD Installation - Considerations
•
o This Smart Thermostat HD requires 24 VAC power, it does not have the option to be battery
powered. This is supplied via a common wire, typically identified as C.
o The Smart Thermostat HD can adapt for situations where there are not enough wires in the
bundle at the install location. For example, if you do not have C-Wire but do have 24 VAC
available at the HVAC unit, or if you have upgraded your HVAC equipment and now require
more control wires. For these scenarios, the Smart Thermostat HD may be installed in a way
that requires only 2 wires at the wall. For instructions on this install configuration and
further information, please find the Installation Guide in the separate Power Plate box.
In the Box / Recommended Tools
•
o Smart Thermostat HD - Thermostat
o Smart Thermostat HD - Display
o Trim Plate
o Wall Screws x2
o Drywall Anchors x2
o Phillips Screwdriver
o Camera
o Pencil
o Needle nose pliers
•
Button
•
Status LED
Advertisement
Summary of Contents for Building 36 B36T40HDRA
- Page 1 Product Manual • Smart Thermostat HD Overview o Smart Thermostat HD Hardware Display Thermostat • Button • Status LED • Installation Precautions o Before installing the Smart Thermostat HD or servicing the HVAC equipment, turn off power to the system. o Leave power off until you have finished installing or servicing the HVAC equipment.
- Page 2 o Power drill – 3/16 inch (#13) drill bit • Smart Thermostat HD Installation – Location o If replacing an old thermostat, the new Smart Thermostat HD can be mounted in its place. If a new location is desired it will be necessary to move the wiring. o New installation and relocation should follow the accompanying guidelines to ensure the most accurate temperature reading and ease of use.
- Page 3 Once all wires are identified and a picture is taken, disconnect all of the wires and remove the existing thermostat. Remember to secure the wires so they do not fall into the wall. o Prep wires if needed Follow these guidelines for safe and secure wire connections: ...
- Page 4 Smart Thermostat HD Installation – Display Install • o Connect the Display to the Thermostat o Once attached the Display will turn on If the Display does not power on after 30 seconds, verify 24 VAC power is appropriately supplied to the Thermostat from the HVAC system. •...
- Page 5 take off the display of the Smart Thermostat HD, hold down the terminal to remove the wire, remove the wire, hold down the opposite terminal, insert the wire fully, place the display of the Smart Thermostat HD back on the backplate, and return power to your HVAC system.
- Page 6 necessary. The setup for these schedules can be found here: o INSERT STEPS We suggest making use • of your smart home supplied schedules as local scheduling is only available when not connected to your smart home How do I reset my Smart I am moving or re-setting up my The Smart Thermostat •...
- Page 7 Note: The Hub or Panel • may be unaware that this procedure was performed, so it is recommended that you remove the Smart Thermostat HD from the Z-Wave network before performing this reset. The Display is not working. The Display may not be Tap the screen which •...
- Page 8 - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY Building 36 Technologies COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. IC Notice This device complies with Industry Canada license-exempt RSS standard(s).
- Page 9 brouillage, et (2) l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Radiofrequency radiation exposure information: This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and the body of any persons, user or bystander in a normal operation mode.