Cleaning And Maintenance; Technical Data - VOLTCRAFT PB-12 Operating Instructions Manual

• T he LEDs (9) indicate the status of the battery during charging.
S teady lit LEDs indicate the actual charging degree (1 LED steady = battery is charged
25% , 2 LEDs = 50%, 3 LEDs = 75%, 4 LEDs = 100%), while flashing lights indicate the
remaining part of the battery which still has to be recharged.
• T he charging time depends on the status of the battery and can last for several hours (see
chapter "Technical data" for charging time of a fully discharged battery).
• O nce the built-in rechargeable battery is fully charged, disconnect the power bank from the
voltage/ current supply. The power bank is now ready to use.
c) charging the built-in rechargeable battery via the USB port of a computer
• Unplug the device which is connected to the power bank's charging output.
I t is not possible to simultaneously use the charging output and recharge the power
bank. In the course of charging, the lighter may not be used as well.
• C onnect the USB power cable included in the delivery with the micro USB adapter.
• U se the USB cable to connect the micro USB port (5) with the USB port of a PC or USB
hub with own power supply unit.
D o not use any USB port of e.g. a keyboard or a USB hub, which are not equipped with
their own power supply; the available current will not be sufficient.
• T he LEDs (9) indicate the status of the battery during charging.
S teady lit LEDs indicate the actual charging degree (1 LED steady = battery is charged
25% , 2 LEDs = 50%, 3 LEDs = 75%, 4 LEDs = 100%), while flashing lights indicate the
remaining part of the battery which still has to be recharged.
• T he charging time depends on the status of the battery and can last for several hours (see
chapter "Technical data" for charging time of a fully discharged battery).
• O nce the built-in rechargeable battery of the power bank is fully charged, disconnect the
micro USB connector from the power bank. The power bank is now ready to use.
d) charging the mobile device
• F irst, disconnect the power bank from the charging cable, then unplug the micro USB con-
nector from the power bank.
I t is not possible to simultaneously use the charging output and recharge the power
bank. Neither the lighter may be used in the course of charging of a mobile device/
smartphone.
• T he power bank is equipped with a charge port capable of providing max. charging current 2 A.
C onnect the USB A port (7) of the power bank to your mobile device/smartphone using a
suitable cable. You may use the enclosed USB power cable and micro/mini USB adapter.
The charging process starts automatically.
• M onitor the charging process. Once the mobile device/smartphone is fully charged (or the
rechargeable battery of the power bank is empty), the power bank will turn off.
• D isconnect the cable connection between your mobile device/ smartphone and the power
bank by unplugging the USB connector of the cable from the USB A port on the power bank
to manually terminate charging.
e) Using the LED flash light
Press the control key (4) 2x briefly and consecutively to turn the white LED (6) on or off.
f) Using UV source
Press the operating button (4) 3x in quick succession to turn on the UV-LED (8). Press the
operating button (4) 1x shortly to turn off the UV-LED. With the UV lamp, you can for example
check bank notes.
g) Using the lighter
• O pen the flap cap (1). A built-in spring raises it to 90°.
• H old down the button (2) until the spiral filament (3) starts glowing orange. Light up your
cigarette and release the button (2).
Never press the button (2) for longer than 20 seconds.
• T hen, shut the flap cap (1) until it snaps in.
W hen the power bank battery is low, the button (2) is inactive and it is impossible to
light a cigarette.
I t is impossible to charge a mobile device/smartphone and use lighter at the same time.
If the button (1) is pressed in the course of mobile device/smartphone charging, the
charging process is terminated automatically.
Do not touch the spiral filament directly, there is a risk of burning!

cLEANING AND MAINTENANcE

The product does not require any maintenance and should never be disassembled for any
reason. The rechargeable battery is permanently installed and cannot be replaced.
Clean the product carefully, e.g. with a soft, clean cloth. Dust can be easily removed with a
soft, clean brush and a vacuum cleaner.
Never use aggressive cleaning agents and no chemicals at all for cleaning; these can lead
not only to discolouration, but can also damage the product.
DISPOSAL
E lectronic devices are recyclable materials and do not belong in the household
waste.
P lease dispose of the device, when it is no longer of use, according to current statu-
tory requirements.

TEcHNIcAL DATA

Charging input ......................................1x micro USB port
Input voltage/current . ............................5 V/DC, max. 500 mA
Charging output . ...................................1x USB port of type A
Output voltage/current . .........................5 V/DC, max. 2 A
Internal rechargeable battery . ...............Lilon, 3.7 V, 5200 mAh
Charging duration . ................................approx. 12 h at fully discharged rechargeable battery
Ambient conditions ............................... T emperature -20 °C to +60 °C, air humidity 30% to
Dimensions (W x H x D) .......................102 x 45 x 22 mm
Weight ..................................................147 g
Legal notice
G
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© copyright 2015 by conrad Electronic SE.
80% relative, not condensing