Table of Contents
Summary of Contents for Hakko Electronics FN-1201
- Page 1 Connection Box FN-1201 Instruction Manual Thank you very much for purchasing the HAKKO FN-1201 (Connection Box). Be sure to read this manual before operating the HAKKO FN-1201. Keep this manual readily accessible for reference.
-
Page 2: Table Of Contents
Table of Contents 1. PACKING LIST ........................1 2. SPECIFICATIONS ........................1 3. WARNINGS, CAUTIONS AND NOTES ................2 4. PART NAMES ........................3 4-1 Front View ..............................3 4-2 Rear View ..............................3 5. INITIAL SETUP ........................4 Installing interface cards ........................4 5-2 Connecting the power cord ........................5 5-3 Connecting the LAN cable ........................ -
Page 3: Packing List
1. PACKING LIST Please check to make sure that all items listed below are included in the package.. HAKKO FN-1201 (Connection Box) ......1 Instruction manual ............1 Power cord ..............1 Power cord Instruction manual HAKKO FN-1201 (Connection Box) 2. SPECIFICATIONS ●FN-1201 AC100 to 240V 50/60Hz... -
Page 4: Warnings, Cautions And Notes
● D o not allow this product to be used by persons (including children) without knowledge or experience without the approval of the administrator. ● Do not allow children to play with this product. ● D o not allow children to perform cleaning or user maintenance without supervision. ● B efore checking the inside of the HAKKO FN-1201 or replacing parts, be sure to disconnect the power plug. Failure to do so may result in electric shock. Failure to comply with the following cautions may result in the risk of electric shock, injury, etc. CAUTION ● Do not allow this product to get wet or operate this product with wet hands. -
Page 5: Part Names
4. PART NAMES 4-1 Front View 4-2 Rear View Blank panels RESET button SELV, non-Hazardous Energy Level POWER switch REBOOT button Inlet Cover bolts Connector (LAN) Fuse... -
Page 6: Initial Setup
5. INITIAL SETUP Installing interface cards WARNING Do not allow this product to be used by persons (including children) without knowledge or experience without the approval of the administrator. Remove a blank panel from the back side. Slide the interface card in so that the card edge connector is inserted as far as it will go. CAUTION •... -
Page 7: Connecting The Power Cord
5-2 Connecting the power cord Plug the power cord into the inlet on the back of the connection box. SELV, non-Hazardous Energy Level 5-3 Connecting the LAN cable Connect the connection box and PC with a LAN cable. ・ Connecting directly LAN cable ・... -
Page 8: Installation
6. INSTALLATION You must be logged into the computer with Administrator user rights in order to install the software. 6-1 IP Address Setting Application settings 6-1-1 Initially installing the software Download “FN1201 connection setting utility .zip” file from Document Portal. Choose the folder to install, and decompress the downloaded file at that folder. 6-1-2 Updating the software Download “FN1201 connection setting utility .zip”... -
Page 9: Operation
7. OPERATION 7-1 Network settings Check that all connections in "5. INITIAL SETUP" have been performed and then switch on the POWER switch of the connection box and switch on the PC. On the PC, start the IP Address Setting Application. In the IP Address Setting Application, set the internet protocol setting (IPv4 or IPv6) and input the IP address, subnet mask, default gateway, and NTP server address, and then click [Send]. -
Page 10: Basic Operation
7. OPERATION (continued) 7-2 Basic operation 7-2-1 Startup Check that all connections in "5. INITIAL SETUP" have been performed and then switch on the POWER switch of the connection box and switch on the PC. Check that the blinking interval of the green LED on the connection box has changed from 0.3 seconds to 2 seconds. -
Page 11: Support For New Models
7-4 Support for new models In order to add support for a new model to the connection box, it is necessary to install the command support file for that model. With the connection box connected to the PC, start the Command Support File Installation Application. - Page 12 HEAD OFFICE 4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN TEL:+81-6-6561-3225 FAX:+81-6-6561-8466 http://www.hakko.com E-mail:sales@hakko.com OVERSEAS AFFILIATES U.S.A.: AMERICAN HAKKO PRODUCTS, INC. TEL: (661) 294-0090 FAX: (661) 294-0096 Toll Free (800)88-HAKKO 4 2 5 5 6 http://www.hakkousa.com HONG KONG: HAKKO DEVELOPMENT CO., LTD. TEL: 2811-5588 FAX: 2590-0217 http://www.hakko.com.hk E-mail:info@hakko.com.hk...