Safeguard Supply LRA-EXTX-L Owner's Manual

LRA-EXTX-L Door hi e E ten er
Owner's Manual
is vic co i s wi Par 5 o
o owing con i ions . is vic
acc an in r r nc inc ing in r r nc
Intro u tion
The A T transmitter connects to a standard wired doorbell.
wired push button outside is pressed, the doorbell dings as usual, and the
T transmitter is triggered and sends a radio signal to a compatible
recei er for notification strobe, chime sounds, etc. .
I ortant otes
• The
A T chime extender can work with both the front door "second"
door of your wired doorbell.
• The transmitter only works with standard wired doorbells that play a "ding" or
"ding dong" sound. It does not work with intercom or ideo doorbells.
• The transmitter works
• owered by a A battery that should last up to years prior to
replacement.
•
imensions are x
• ust be used in conjunction with a
or the A .
attery Installation
. pen the front co er using a small flat head screw dri er see
abo e .
. Insert included A battery into the battery compartment see
abo e . nsure to remo e the plastic wrap around the battery
prior to installing.
. ress the "front door" or "back door" button. You should see a red
to show the transmitter is working correctly.
rogra ing the LRA-EXTX to Your
The A T transmitter wires directly into the wired doorbell door
chime inside your home typically hanging in the foyer .
recommend you pair program the
recei er prior to wiring mounting the transmitter.
multi oned, meaning each transmitter is paired to a one with each
one ha ing a distinct melody assigned to it. If your wired doorbell is
connected to two doors front door and second door , then each door
outdoor wired push button will correspond to a one on the
recei er. The button labeled "front door" on the
r s ra ion o is vic is s
a no ca s ar in r r nc . .
a a ca s n sir
A wired door chimes.
x .
A recei ers such as the
ire Doorbell
A T to a compatible
A recei ers are
A T will wire
rogra
to the front doorbell button on your existing wired doorbell
the "back door" button on the
doorbell button on your existing wired doorbell in your home. If
the existing wired doorbell in your home does not use or ha e a
"back" or "second" doorbell button, you do not ha e to program
the "back door" button .
ach
pairing that recei er to a transmitter as each are slightly different.
c o
is vic s
o ra ion.
The instru tions belo outline ho to air the trans itter to
the LRA-D RXA-L.
hen the
• nsure the battery is installed in the
A
the compatible recei er is powered on. nsure the plastic
A
wrap is remo ed from battery prior to inserting into
transmitter.
•
selector button for approximately three seconds until you
see " one " flashing on the recei er.
release the one selector button. The flashing one signifies
that this one is in programming pairing mode.
• If you are programming the "front door" button on the
A
step. If you are programming the
transmitter to a different one, press the one selector
A A
button again to scroll to the desired one.
•
ext you will select the
desired melody for that
one by scrolling through
the melodies using the
melody selector button ♫
located next to one
selector button .
nce you hear the desired
•
melody, stop pressing the
melody selector button ♫.
ress the "front door" button
•
on the
• A red
the button.
the strobe on the recei er will flash once, and the next
one s
If you would like to program the "back door button," follow
•
this step. If not, skip to the next step.
e
scroll to the desired melody you desire for this one.
A
you hear the desired melody, press the "back door button"
on the transmitter to pair the transmitter to this one
To exit programming pairing mode, scroll past one four
•
on the recei er using the
scrolling past one four, none of the one lights should be
A
flashing. This shows you are no longer in pairing
programming mode.
ing the LRA-EXTX to Your
A
A recei er will come with instructions on programming
pen the front co er of the recei er. ress hold the one
T transmitter to this one, mo e to the next
A T transmitter
.
should flash on the transmitter after you press
hen the transmitter has paired to the recei er,
will start blinking.
one selector button. After
ire Doorbell ont
T will wire to the back
A T transmitter
hen it starts to flash,
A T
sing the ♫ button,
nce