Advertisement
qualified contractor. Wiring procedures and connections
should be in accordance with the National Electric Code
(CEC & NEC) and local codes.
Connect the supply wire into a properly rated recess box.
!
NOTE: Consult your local electrical code for applicable
wire gauge.
Connect L1 from the power supply to the L1 labelled wire
from the unit, connect the L2 wire from the power supply to
the L2 labelled wire from the unit, and connect the ground to
the ground screw on the unit.
Wiring Diagram
Thermal Cutout
Operation
W ARNING: A minimum distance of 3 ft. (0.9 m) must be
maintained in front of the heater.
W ARNING: This heater must be properly installed before
it is used.
The manual controls are located on the right hand side, at
the top of the appliance.
1. Press the power button to power on the unit. An indica-
tor light beside the power button shows when the unit is
powered on.
2. The indicator light below the heat symbol is illuminated
when the elements are actually heating.
!
NOTE: Should the heater overheat, an automatic ther-
mal cut out will turn the heater off. The heater will reactivate
once the heater has cooled.
Controlling the temperature
The heater is fitted with an adjustable thermostat, enabling
the room temperature to be controlled by adjusting the slider
accordingly.
1. The frost protector setting (
perature of approximately 5 °C (41 °F) and may be used
for protection against frost.
2. The MAX setting represents a room temperature of ap-
proximately 30 °C (86 °F).
3. Adjust the slider to your individual comfort level. When
the room temperature has reached the desired level, the
power to the elements will be reduced. The heater will
then maintain the room temperature at the chosen level.
1367 Industrial Road
Cambridge ON Canada N1R 7G8
1-888-346-7539
www.dimplex.com
In keeping with our policy of continuous product improvement, we reserve the right to make changes without notice.
© 2013 Dimplex North America Limited
L1
L2
Ground
Temperature
Sensor
*
) represents a room tem-
Figure 3
*
Maintenance
WARNING: Disconnect power and allow the unit to com-
pletely cool before attempting any maintenance or clean-
ing to reduce the risk of fire, electric shock, or damage to
persons.
CAUTION: The heater should not be operated with an
accumulation of dust or dirt on or in the unit, as this can
cause a build up of heat and eventual damage. For this
reason the heater must be inspected regularly, depending
upon conditions and at least at yearly intervals.
The outer surface can be wiped with a soft damp cloth.
!
NOTE: Do not use scouring powder or furniture polish,
as these can damage the surface.
Dust that collects within the unit can be removed from the
outside using a vacuum cleaner.
Warranty
The Manufacturer warrants the convector heater and components of the
enclosed product against any defect in material or workmanship for a period
of two years from the date of purchase, with the exception of the elements
which are warranted to be free from defect in material and workmanship
for ten years. In full satisfaction of any claims under this Warranty the
Manufacturer will repair or replace without charge, in its factory or in the field
as it alone may decide, any parts which in its opinion are defective.
The Manufacturer shall not be responsible for any transportation or shipping
costs in relation to such repair or replacement except as specifically
assumed by it. Misuse of this product or repairs by persons other than the
Manufacturer's authorized personnel without the Manufacturer's written
approval, will void this Warranty.
This Warranty is in lieu of all other warranties or conditions whether
expressed or implied including but not limited to those of merchantability or
fitness for purpose and shall constitute the sole remedy of the Purchaser
and the sole liability of the Manufacturer in respect of the sale of the product,
whether in the nature of breach or breach of fundamental term, or of
negligence or otherwise.
The Manufacturer shall not be liable for any special, indirect or consequential
damages or for any damages resulting from removal or replacement of
a convector heater subject to warranty claim without the Manufacturer's
authorization.
Any claims under this Warranty must be submitted in writing to the Service
Manager, Dimplex North America Ltd., 1367 Industrial Rd., Cambridge,
Ontario N1R 7G8, Canada.
MAX
Advertisement
