Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for LG Industrial Systems SV-iS5 Series
- Page 1 All manuals and user guides at all-guides.com User Manual MODBUS-RTU Option Board for SV-iS5 Series Read this manual carefully before using the MODBUS-RTU Option board and follow the instructions exactly. After reading this manual, keep it at handy for future reference.
- Page 2 All manuals and user guides at all-guides.com...
-
Page 3: Safety Precautions
All manuals and user guides at all-guides.com Thank you for purchase of LG Modbus-RTU Option Board! SAFETY PRECAUTIONS Always follow safety precautions to prevent accidents and potential hazards from occurring. Safety precautions are classified into “WARNING” and “CAUTION” in this manual. Indicates a potentially hazardous situation which, if not avoided, WARNING can result in serious injury or death. - Page 4 All manuals and user guides at all-guides.com...
-
Page 5: Specification
All manuals and user guides at all-guides.com INTRODUCTION By using a MODBUS-RTU Option board, SV-iS5 inverter can be connected to a MODBUS-RTU network. 1.1. When you use the MODBUS-RTU Option Card … Inverter can be controlled and monitored by the sequence program of the PLC or other master module. The card provides a terminal block for an RS-485 interface. -
Page 6: Product Detail
All manuals and user guides at all-guides.com 2.3. Communication Specification Items Specifications Communication speed 1200 /2400/4800/9600/19200 bps Selectable Control procedure Asynchronous communication system Communication system Half duplex system Character system Binary (8 bit) Start/Stop bit 1 bit Error check (CRC16) 2 byte Parity check None... -
Page 7: Installation
All manuals and user guides at all-guides.com 3.2. Status LED CPU LED Indicates normal operation of the board when blinking once per second. RXD LED Receiving 485 signal TXD LED Responding to 485 signal On and Off intermittently Wrong DATA received (Normal operating) Blinking with CPU LED at the same DPRAM communication fault ERR LED... -
Page 8: Troubleshooting
All manuals and user guides at all-guides.com TROUBLE SHOOTING If communications cannot be established with the drive, there are four LEDs on the Modbus card to aid in troubleshooting. The CPU LED should blink once per second to indicate that the modbus card is interfacing with the inverter main PCB properly. - Page 9 All manuals and user guides at all-guides.com 5.1.3. ERR LED State Indicates Corrective measures On/off from time The card is receiving invalid data such Normal to time as noise. Blinking with CPU Trouble with the Modbus card Cycle the Inverter power. If the LED at the same problem persists, contact LG time...
- Page 10 All manuals and user guides at all-guides.com PARAMETER CODE (HEX) <Common> Area accessible regardless of inverter models (Note 3) Parameter Parameter Name Unit Read/Write Data Value (Hex) Address 0x0000 Drive model 4: SV-iS5 0: 0.75 1:1.5 2:2.2 3: 3.7 4: 5.5 5: 7.5 6: 11 7: 15 8: 18.5 9: 22 A: 30...
- Page 11 All manuals and user guides at all-guides.com Parameter Parameter Name Unit Read/Write Data Value (Hex) Address BIT 7 : DC Braking BIT 8 : Stopping BIT 9 :Not Available BIT 10 : BrakeOpen BIT11: Forward Run Command BIT 12 : Reverse Run Command Bit 0:OCT1, Bit 1: OV, Bit 2: EXT-A Bit 3: BX, Bit 4:OCT2,...
- Page 12 All manuals and user guides at all-guides.com Address Description Default Maximum Minimum Unit 5105 DRV#05 Step freq - 1 1000 MaxFreq startFreq 0.01Hz 5106 DRV#06 Step freq - 2 2000 MaxFreq startFreq 0.01Hz 5107 DRV#07 Step freq - 3 3000 MaxFreq startFreq 0.01Hz...
- Page 13 All manuals and user guides at all-guides.com Address Description Default Maximum Minimum Unit 5227 FU1 #39 Energy save 5232 FU1 #50 ETH select 5233 FU1 #51 ETH 1min ETH Cont 5234 FU1 #52 ETH Cont 5235 FU1 #53 Motor type 5236 FU1 #54 OL level...
- Page 14 All manuals and user guides at all-guides.com Address Description Default Maximum Minimum Unit 5321 FU2 #33 Rated-Curr (Note4) 2000 0.1A 5322 FU2 #34 Noload-Curr (Note4) 2000 0.1A 5324 FU2 #36 Efficiency (Note4) 5325 FU2 #37 Inertia rate 5327 FU2 #39 Carrier freq 0.1kHZ 5328...
- Page 15 All manuals and user guides at all-guides.com Address Description Default Maximum Minimum Unit 5355 FU2 #85 2nd F-boost 0.1% 5356 FU2 #86 2nd R-boost 0.1% 5357 FU2 #87 2nd Stall 2nd ETH 5358 FU2 #88 2nd ETH 1min Cont 2nd ETH 5359 FU2 #89 2nd ETH Cont.
- Page 16 All manuals and user guides at all-guides.com Address Description Default Maximum Minimum Unit 541E I/O #30 Dec time - 3 6000 0.1sec 541F I/O #31 Acc time – 4 6000 0.1sec 5420 I/O #32 Dec time – 4 6000 0.1sec 5421 I/O #33 Acc time –...
- Page 17 All manuals and user guides at all-guides.com < EXT Group > Address Description Default Maximum Minimum Unit 5501 EXT #01 Sub B/D 5502 EXT #02 P4 define 5503 EXT #03 P5 define 5504 EXT #04 P6 define 5505 EXT #05 V2 mode 5506 EXT #06...
- Page 18 All manuals and user guides at all-guides.com < COM Group > Address Description Default Maximum Minimum Unit 5601 COM #01 Opt B/D 5602 COM #02 Opt mode 5603 COM #03 Opt version 1.00 Note) Inverter Station # and Baud rate Setting: I/O-46, 47 COM-01 [Opt B/D] Indicates Option boards installed.
- Page 19 All manuals and user guides at all-guides.com LG Industrial Systems Co., Ltd. LGIS constantly endeavors to improve its product so that information in this manual is subject to change without notice. Visit Our Website: http://www.lgis.com/ August 8, 2002 Publication #: 10310000393...
Need help?
Do you have a question about the SV-iS5 Series and is the answer not in the manual?
Questions and answers