Page 1
® Instruction Manual May be covered by one or more of the following: U.S. Patents #4538297, 4647876, 4696044, 4745309, 4881047, 4893099, 5124657, 5263091, 5268527, 5319713, 5333201, 5402498 and 5493617. Other patents pending. Foreign patents pending. HUSH ® is a registered trademark of GHS Corporation...
Page 2
Also, bundle audio cables separately from the AC power cables. These steps will help insure compliance with the Directive(s). For more information about other Rocktron products, please see your local dealer or one of our importers closest to you (listed on the enclosed warranty sheet).
The HUSH Ultra features True Bypass, an LCD display and programmable presets with MIDI control allowing you to tailor your HUSH settings on individual presets to suit your needs. The HUSH Ultra provides BOTH 1/4” and XLR inputs and outputs, and is easy to setup and easy to use.
Page 5
OPERATING PRECAUTIONS NOTE: IT IS VERY IMPORTANT THAT YOU READ THIS SECTION TO PROVIDE YEARS OF TROUBLE FREE USE. THIS UNIT REQUIRES CARE- FUL HANDLING. All warnings on this equipment and in the operating instructions should be adhered to and all operating instructions should be followed. Do not use this equipment near water.
STORE/EDIT button This button is used to STORE any changes you make to presets. It is also used to put the HUSH Ultra into "PRESET EDIT" Mode. See PRESET EDIT mode later in this manual for more details on this function.
CH. A (MONO) IN jacks This XLR and ¼" mono jack provide inputs to the left channel of the HUSH Ultra. Use either the XLR jack or the ¼" jack when connecting, but not both together. When using only one input use the "CH. A (MONO) XLR or ¼"...
GATE THRESHOLD CONTROL The other half of the HUSH Ultra consists of a noise gate. A noise gate completely shuts off the output signal when the input signal level drops below a prescribed threshold level (volume). On the HUSH Ultra, this threshold is determined by the Gate Threshold control on the front panel.
To maximize the performance of the HUSH Ultra, it is necessary to understand its front panel controls and how they work together. By understanding how these controls work, it will be easier to cor- rectly set up the HUSH Ultra to suit any application.
Page 15
This means that if a signal is present at the input which consists of primar- ily bass components, the dynamic filter will reduce mid or high band noise. If no mid or high band information is present, the filter will close down to a pre-set cut-off point of 1kHz (allowing only frequencies of 1kHz and below to pass).
To access these FUNCTIONS and PARAMETERS, you must first enter into the "EDIT MODE." The HUSH Ultra is set up to allow you to first access each function (via the FUNCTION SELECT knob), then the parameter list for each function (via the PARAMETER SELECT knob) and finally the adjustable value for each parameter (via the PARAMETER ADJUST knob).
Ultra unaffected. When "OFF" is selected the unit is active and True Bypass is off and HUSH is active. TRUE BYPASS uses high quality relays to perform a total bypass of the HUSH ULTRA when us- ing the ¼ jacks.
HUSH Function ® HUSH I/O The HUSH I/O parameter simply determines whether the HUSH® circuit is active for the current preset. When "IN" is selected the HUSH is active. When "OUT" is selected the HUSH is "OFF". The EXP THRESHOLD (Expander Threshold) parameter determines the level at THRESH1 which downward expansion begins.
The PRESET MAP function allows you to globally turn ON/OFF the PRESET MAPPING function. The preset mapping allows the HUSH Ultra to receive a Program Change from a MIDI Controller for one preset, but to actually recall a different preset. See PRESET MAPPING section later in this manual for more detailed information on PRESET MAP- PING.
Page 20
GLOBAL Function continued..GATE THRESHOLD 3 control is used to determine the level at which the gate will GATE THRESH3 begin to operate. As the input signal drops below this level, the gate will activate and downward expansion will begin. Note that this is only used with the MIDI MCC Link is active.
MCC LINK is desired. When the CTRLINK is on and you are out of the EDIT MODE and you have sent any of the mapped controllers to the Hush Ultra the Hush Threshold and Gate Threshold controls will automatically map to the appropriate selection HUSH_ THRSH_A , B, C or D.
Note: PRESET MAP in the GLOBAL FUNCTION must be set to ON for mapping to be active. MIDI DUMP/LOAD Function This function allows you to dump 1 preset from one HUSH Ultra to a second 1 PR DUMP/LOAD HUSH Ultra or a MIDI sequencer device.
MIDI DUMP/LOAD VERSION NUMBER Display Description The LCD display on the HUSH Ultra provides you with the information about the preset you are in: Top line of display will show: PRESET NUMBER - Displays the Preset Number you have selected.
SELECTING A PRESET: There are two ways to select a preset on the HUSH Ultra. You can either turn the PRESET knob to the desired preset you wish to recall. The display will show the selected preset number. u s e r 1.
CHANGING PRESET PARAMETERS STEP 1 - Enter EDIT MODE by pressing the STORE/EDIT button as shown above. When in EDIT MODE the display will show you are in "EDIT MODE" on the top line. * * E D I T M O D E * * STEP 2 - To access the first "FUNCTION"...
STORING CHANGED PRESET PARAMETERS STORE CHANGES AT THE SAME PRESET While viewing a function or parameter title, press the STORE button to start the store procedure. The words "STORE AT PRESET" will now be flashing under the changed preset name as shown below. If you would like to store the changes made at the current preset, simply press the STORE/EDIT but- ton again and the changes will be stored.
To begin the Title Edit function, turn the FUNCTION SELECT knob clockwise until Step 1 the HUSH Ultra displays "TITLE EDIT". * * t i t l e e d i t Turn the PARAMETER SELECT knob clockwise to initiate the Title Edit mode.
Page 29
NOTE: The STORE button must be pressed to save the new title. Exiting the Title Edit func- tion before pressing the STORE button will erase any editing that was done in Title Edit. Also, after flashing "STORED", the HUSH Ultra will exit the title edit mode and return to the main preset number.
The PARAMETER ADJUST selects the PRESET that will be recalled (Number on the right side of the screen) when the received program change is executed. In above example the HUSH ULTRA received a PROGRAM CHANGE from a midi controller for preset 1. The actual preset recalled will be 15! Note: PRESET MAP in the GLOBAL FUNCTION must be set to ON for map- ping to be active.
MIDI DUMP/LOAD Any or all of the HUSH Ultra's presets may be dumped to another HUSH Ultra a sequencer or MIDI utility program using a PC midi interface to create a ( .syx ) file. All the information about the presets you have created will be dumped consisting of parameter values, title characters and controller assign- ments.
Page 32
M I D I D U M P / L O A D 1 d u m p e d To BULK DUMP all presets to another HUSH Ultra or upload them to a Sequencer Step 6 or Computer using a PC MIDI interface along with a MIDI Utility program, use the...
CONNECTIONS section of this manual. Please note that though the HUSH Ultra has a 7 Pin din connector any standard 5 pin MIDI cord may be used for device connections. This 7-pin DIN connector must be connected to the MIDI OUT jack of the transmitting MIDI device via a standard MIDI cable, or to the MIDI THRU jack of the preceding MIDI device (if the HUSH Ultra is within a chain of MIDI devices).
PHANTOM POWER This 2.5mm PIN jack offers the ability to power Rocktron MIDI foot controllers from a 7-pin MIDI cable which connects from the Rocktron MIDI foot controller to the MIDI IN jack on the rear panel of HUSH Ultra.