1. Manuals
  2. Brands
  3. DPI Manuals
  4. Media Converter
  5. KYNERGY 10-13B020T Series
  6. Instruction manual

DPI KYNERGY 10-13B020T Series Instruction Manual

Dc-dc converters
Hide thumbs
Table of Contents

Advertisement

Quick Links

®
KYNERGY
AND INTELLIPHASE POWER
GALVANICALLY ISOLATED & NON-ISOLATED – HI-EFFICIENCY
PRODUCT MODELS:
Non-Isolated Input To Output (Isolated From Chassis) KYNERGY
10-13B020Txx
11-13B020Txx
10-13D020Txx
11-13D020Txx
Isolated Input to Output And From Chassis INTELLIPHASE POWER
12-13D020Txx
12-13D030Txx
12-13F030Txx
Output Connector:
Manual P/N:
Copyright © 2014 DPI
24V Input, 13V 300W Dual Output, Switched + Continuous
24V Input, 13V 300W Single Output, Switched
36/48V Input, 13V 300W Dual Output, Switched + Continuous
36/48V Input, 13V 300W Single Output, Switched
36/48Vdc Input, 13Vdc 300W Single Output, Switched
36/48Vdc Input to 13Vdc 400W Single Output, Switched
72Vdc Input to 13Vdc 400W Single Output, Switched
xx = 08
xx = 50
xx = 55
xx = 95
xx = 98
xx = 99
IMPORTANT: READ AND SAVE THIS SAFETY
INSTRUCTION MANUAL.
MNUL0023 Rev.6
Diversified Power International
414 Century Court
Piney Flats, TN 37686
(423) 538-9002 (423) 538-9202 (fax)
www.DPIpower.com
®
SERIES DC-DC CONVERTERS
Terminal Block Connector
Deutsch Style Connector.
Delphi Connector
Multi-Type I/O Connector
Flying Output Leads – no Connector supplied
Customer Specified Special-App Connector
1
®
Series:
®
Series:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KYNERGY 10-13B020T Series and is the answer not in the manual?

Questions and answers

Summary of Contents for DPI KYNERGY 10-13B020T Series

  • Page 1 Delphi Connector xx = 95 Multi-Type I/O Connector Flying Output Leads – no Connector supplied xx = 98 xx = 99 Customer Specified Special-App Connector IMPORTANT: READ AND SAVE THIS SAFETY INSTRUCTION MANUAL. Manual P/N: MNUL0023 Rev.6 Copyright © 2014 DPI...

  • Page 2: Table Of Contents

    1.5. Very high electrical energy conversion efficiency exceeding 91%, very low radiated and conducted noise emissions. 2. INTRODUCTION • The Diversified Power International (DPI) DC-DC Galvanic Isolated DC-DC Converter series represents a design performance breakthrough allowing superior regulation over a very large input range.

  • Page 3: User Safety

    3.3. Construct cabling using DPI Approved and DPI supplied Connector Housing and Connector pins and sockets. 3.4. The use of undersized conductors is STRICTLY prohibited. Ensure that any wiring added to the input or output can safely carry the DC Current expected.
  • Page 4 4.5. NEVER smoke or allow a spark or flame in vicinity of battery. 4.6. Be extra cautious not to drop a metal tool onto battery. It might spark or short circuit battery or other electrical part that may cause an explosion. 4.7.
  • Page 5 5.5. Ensure Vehicle Ignition Key is off and turn Battery Disconnect off so that the Battery Pack is completely disconnected from Vehicle and loads. If a disconnect switch is not available, disconnect Positive and Negative Cables from Battery Pack. Confirm disconnection by checking with a voltmeter from frame to positive and negative battery terminals.

  • Page 6: Operation

    5.8. Converter relies on conduction of heat to ambient air. An unpainted metal surface of 36sq.in. and unobstructed air flow is required for maximum output. 5.9. Enable the converter by engaging the Ignition Key Switch. Using a voltmeter, check and confirm output voltage from Converter High Power Output Channel is 13.0Vdc +/-0.5V and that the polarity of the output is correct.
  • Page 7 8. WIRING DIAGRAM DRAWINGS...
  • Page 10 IMPORTANT: CONVERTER IS NOT A BATTERY CHARGER AND DOES NOT CONTAIN A BACKFEED DIODE PROTECTOR. IF THE BATTERY CONNECTED TO THE CONVERTER INPUT FALLS BELOW THE VOLTAGE OF THE BATTERY CONNECTED TO THE OUTPUT, THE CONVERTER’S INPUT FUSING WILL OPEN CAUSING A PERMANENT NON-WARRANTY CONDITION.

  • Page 11: Mount Drill Templates

    Note: Base Plate Design is intentionally sized to allow for a Drop-In Replacement mounting into Club Car 2-hole mount pattern. NON-ISOLATED CONVERTER DRILL TEMPLATE Note: DPI’s 2-Hole Base Plate Design intentionally sized to allow Drop-In Replacement mounting into many competitors’ two or four or six-hole mounting patterns.

  • Page 12: Warranty

    Diversified Power International LLC (DPI) warrants exclusively to the original purchaser that this product will be replaced or repaired, at DPI’s option, if it fails during the first 2 years after date of purchase due to a defect in material or workmanship or 3000 hours of operation (internal time keeping mechanism employed).

This manual is also suitable for:

Kynergy 11-13b020t seriesKynergy 10-13d020t seriesKynergy 11-13d020t seriesIntelliphase power 12-13d020t seriesIntelliphase power 12-13d030t seriesIntelliphase power 12-13f030t series

Table of Contents