Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Lincoln Electric K1669-4
- Page 1 Operator’s Manual Lamp Kit with Arc Sensor Authorized Service and Distributor Locator: www.lincolnelectric.com/locator Save for future reference Date Purchased Code: (ex: 10859) Serial: (ex: U1060512345) IM10366-B | Issue D ate Nov-21 © Lincoln Global, Inc. All Rights Reserved.
- Page 2 THANK YOU FOR SELECTING A QUALITY PRODUCT BY KEEP YOUR HEAD OUT OF THE FUMES. DON’T get too close to the arc. LINCOLN ELEC TRIC. Use corrective lenses if necessary to stay a reasonable distance away from the arc. READ and obey the Safety Data PLEASE EXAMINE CARTON AND EQUIPMENT FOR Sheet (SDS) and the warning label DAMAGE IMMEDIATELY...
-
Page 3: Section A: Warnings
P.O. Box 351040, Miami, Florida 33135 or CSA Standard W117.2. A Free copy of “Arc Welding Safety” booklet E205 2.a. Electric current owing through any conductor is available from the Lincoln Electric Company, 22801 causes localized Electric and Magnetic Fields (EMF). St. Clair Avenue, Cleveland, Ohio 44117-1199. -
Page 4: Electric Shock Can Kill
SAFETY ELECTRIC SHOCK ARC RAYS CAN BURN. CAN KILL. 3.a. The electrode and work (or ground) circuits are 4.a. Use a shield with the proper filter and cover plates to protect your electrically “hot” when the welder is on. Do eyes from sparks and the rays of the arc when welding or not touch these “hot”... - Page 5 SAFETY WELDING AND CUTTING CYLINDER MAY EXPLODE IF SPARKS CAN CAUSE DAMAGED. FIRE OR EXPLOSION. 7.a. Use only compressed gas cylinders containing the correct shielding gas for the process used 6.a. Remove fire hazards from the welding area. If and properly operating regulators designed for this is not possible, cover them to prevent the welding sparks the gas and pressure used.
- Page 6 LAMP KIT WITH ARC SENSOR SAFETY As a rule of thumb, for many mild steel electrode, if the air is visibly Ventilation clear and you are comfortable, then the ventilation is generally There are many methods which can be selected by the user to adequate for your work.
- Page 7 TLV and PEL values are as of October 2013. Always check Safety and 313 of the Emergency Planning and Community Right- Data Sheet (SDS) with product or on the Lincoln Electric website at to-Know Act of 1986 and of 40CFR 370 and 372.
- Page 8 LAMP KIT WITH ARC SENSOR TABLE OF CONTENTS...
-
Page 9: Installation
AD1221 - Lamp Kit with Arm Control Box for wall mounted systems LAMP KIT Operating 24 VAC Voltage Bulb HALOGEN, 35W K1669-4 Operating 115 V, 1~, 60 Hz, 16 A Voltage/Current 230 V, 1~, 50 Hz, 8 A K1669-10 Operating 230 V, 3~, 50 Hz, 6.8 A... -
Page 10: General Description
LAMP KIT WITH ARC SENSOR INSTALLATION Read this entire installation section before you start installation. GeneRal DeScRiPtion The Lamp Kit incorporates a work lamp with hood-mount switches Safety Precautions for both the lamp and the Stationary Extraction Fan. The 35W lamp fits in the hood of the arm, to provide a convenient, Do not attempt to use this equipment until you have positionable light at the workspace. - Page 11 FIGURE A.3 See Figure A.3. inStallinG tHe laMP Kit witH aRc SenSoR The K1669-4 Lamp Kit with Arc Sensor can be installed with: • K1656-9 Prism 2400 Stationary Fan with a • K1655-8 LFA 3.1, 10 ft. Arm, a • K1655-9 LFA 4.1, 13 ft. Arm, or a •...
- Page 12 LAMP KIT WITH ARC SENSOR INSTALLATION FIGURE A.6 RoutinG tHe connectinG cable Roll back the rubber bands on each flexible hose joint in the arm, to allow access to the arm mechanism. Zip Tie to this side of square tube If installing with arm: (keeps wire above See Figure A.5 Route the connecting cable through the four cable...
- Page 13 LAMP KIT WITH ARC SENSOR INSTALLATION (continued) RoutinG tHe connectinG cable FIGURE A.7 If installing with an LTA 2.0 Telescopic Arm: Route the connecting cable through the arm, securing it to the telescopic mechanism in two places with cable ties as shown in Figure A.7.
- Page 14 LAMP KIT WITH ARC SENSOR INSTALLATION FIGURE A.9 inStallinG tHe contRol boX; K1669-4 anD K1669-10 7.086 in (180.00 mm) WARNING Make sure Prism 2400 60Hz (K1656-9) is connected with 60Hz 115/230V power supply. Similarly Prism 2400 50Hz (K2497-13) is connected to 50Hz 115/230V power supply.
-
Page 15: Operation
LAMP KIT WITH ARC SENSOR OPERATION OPERATION Only qualified personnel should operate this equipment. ADDITIONAL SAFETY PRECAUTIONS Read and understand this entire section before operating Always operate this equipment with the filter and arm your Lamp Kit with Arc Sensor. installed and all covers in place as these provide maximum protection from moving parts and insure proper vacuum operation and cooling air flow. - Page 16 LAMP KIT WITH ARC SENSOR INSTALLATION FIGURE A.11 inStallinG tHe contRol boX - wall MounteD 6.00 in (152.50 mm) SySteMS (aD1221) WARNING Make sure the transformer tapping to match with the power supply voltage. Mount the connection box to the wall using four screws (not included) as shown in Figure A.11.
- Page 17 LAMP KIT WITH ARC SENSOR OPERATION OPERATION Only qualified personnel should operate this equipment. ADDITIONAL SAFETY PRECAUTIONS Read and understand this entire section before operating Always operate this equipment with the filter and arm your Lamp Kit with Arc Sensor. installed and all covers in place as these provide maximum protection from moving parts and insure proper vacuum operation and cooling air flow.
-
Page 18: Maintenance
LAMP KIT WITH ARC SENSOR MAINTENANCE MAINTENANCE RePlacinG tHe HaloGen bulb WARNING When the halogen bulb burns out, it is necessary to replace it. This product has been designed to function without problems for a long time with a minimum of maintenance. •... -
Page 19: Troubleshooting
LN-25 PLC TROUBLESHOOTING Observe all Safety Guidelines detailed throughout this manual PROBLEM POSSIBLE AREAS OF RECOMMENDED COURSE OF ACTION (SYMPTOMS) MISADJUSTMENT(S) Lamp does not illuminate. Connection cable damaged or defective. Check and repair or replace if necessary. Bulb loose or burned out. Tighten the bulb or replace it if necessary. - Page 20 LAMP KIT WITH ARC SENSOR DIAGRAMS...
- Page 21 LAMP KIT WITH ARC SENSOR DIAGRAMS...
- Page 22 LAMP KIT WITH ARC SENSOR DIAGRAMS...
- Page 23 LAMP KIT WITH ARC SENSOR DIAGRAMS...
- Page 24 WARNING Do not touch electrically live parts or Keep flammable materials away. Wear eye, ear and body protection. electrode with skin or wet clothing. Insulate yourself from work and AVISO DE ground. Spanish PRECAuCION No toque las partes o los electrodos Mantenga el material combustible Protéjase los ojos, los oídos y el bajo carga con la piel o ropa moja-...
- Page 25 WARNING Keep your head out of fumes. Turn power off before servicing. Do not operate with panel open or Use ventilation or exhaust to guards off. remove fumes from breathing zone. AVISO DE Spanish PRECAuCION Los humos fuera de la zona de res- Desconectar el cable de ali- No operar con panel abierto o piración.
- Page 26 We respond to our customers based on the best information applicable OSHA PEL and ACGIH TLV limits. in our possession at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such information or advice.