Table of Contents
Advertisement
Quick Links
1
Adjustable mounting solutions for the Indus
trial PCs S15P , S19P , S21Wx and from C‐Series
noax part no.:
14950
noax part no.:
14951
14952
3095-US-1.2
Product Information
Table Stand adjustable (S15P/S19P/S21Wx/C‐Series)
Wall Mount Bracket adjustable (S15P/S19P/S21Wx)
Mount on Stainless Steel Floor Stand (S15P/S19P/S21Wx)
www.noax.com
Adjustable mounting solutions
S15P / S19P / S21Wx / C‐Series
Page 1 of 14
Advertisement
Table of Contents
Summary of Contents for noax 14950
- Page 1 Product Information Adjustable mounting solutions S15P / S19P / S21Wx / C‐Series Adjustable mounting solutions for the Indus trial PCs S15P , S19P , S21Wx and from C‐Series noax part no.: 14950 Table Stand adjustable (S15P/S19P/S21Wx/C‐Series) noax part no.: 14951...
-
Page 2: Intended Use
The adjustable mounting solutions are intended to be used in industrial and technical environment in addition with the noax Industrial PCs S15P , S19P , S21WP and S21WR. Additionally the adjustable Table Stand is intended to be used together with the noax Industrial PCs C15, C15P , C19 and C21W. -
Page 3: General Information
If one of these checks is negative, the mounting solution have to be put out of operation. Keyholes in the mounting brackets of the mounting solutions allow noax Industrial PCs to be mounted easily and conveniently. - Page 4 If the Industrial PC is tilted more than 45° or the Table Stand stands not secure, the Table Stand have to be fastened to the mounting surface! noax recommends the fastening to the mounting surface. To do this, use all 4 holes in the bottom of the table stand.
-
Page 5: Dimensional Drawings
Pivoting range with mounting holes An optional protection earth can be connected to one of the 0.18 inch [4.5 mm] drill holes on the right and left side of the table stand (see marking ”A”). 3095-US-1.2 www.noax.com Page 5 of 14... - Page 6 " Using a size 4 Allen key to hold the screw in place, screw the M5 cap nut on tightly with an SW 8 socket wrench, box wrench or open end wrench (1.5 Nm torque). Page 6 of 14 www.noax.com 3095-US-1.2...
- Page 7 5, notes for handling the mounting solutions can be found in chapter 6. Scope of delivery and specifications Fig. 10: Scope of delivery for adjustable Wall Mount Bracket (S15P/S19P/S21Wx) noax part no.: 14951 Description: Wall Mount Bracket adjustable (...
- Page 8 An optional protection earth can be connected to one of the four 0.18 inch [4.5 mm] drill holes on the right and left side of the wall mount bracket (see marking ”A”). Pay attention to the orientation of the wall mount bracket while installing. (see marking ”TOP”) Page 8 of 14 www.noax.com 3095-US-1.2...
- Page 9 S15P / S19P / S21Wx / C‐Series Mount on Stainless Steel Floor Stand The Mount on Stainless Steel Floor Stand is intended to be used only on a noax Stain less Steel Floor Stand (part no. 13259). Additionally pay attention to the product information of the Stainless Steel...
- Page 10 An optional protection earth can be connected to one of the 0.18 inch [4.5 mm] drill holes on the right and left side of the mounting bracket (see marking ”A”). Page 10 of 14 www.noax.com 3095-US-1.2...
- Page 11 If the position of the Stainless Steel Floor Stand has to be changed, please follow this steps: " Remove connector protection and cables from the noax Industrial PC " Remove the Industrial PC from the mounting bracket " Remove the top of the Stainless Steel Floor Stand with the mounting bracket "...
-
Page 12: Safety Instructions
This will make it easier to hang the housing in the “keyholes” of the mounting bracket. Fig. 22: Mounting screw with 5 mm gap Fig. 23: Mounting bracket ready for installation Page 12 of 14 www.noax.com 3095-US-1.2... - Page 13 " Following this, tighten the mounting screws (size 5 Allen key, 7.5 Nm torque). Fig. 25: IPC ready hanging in the keyholes of the mounting brackets 3095-US-1.2 www.noax.com Page 13 of 14...
- Page 14 " Tighten both locking handles. " Lift the Industrial PC slightly and tighten the locking handles again. This will improve the click‐in position again. noax Technologies AG noax Technologies Corp. Am Forst 6 5265 Parkway Plaza Boulevard, Suite 110...