Page 1
NOTE: Vax recommends that you raise the height of the brush bar when using this cleaner on lino and hard flooring. Vax cannot be held responsible for damage to these surfaces if the customer fails to take notice of this recommendation.
Page 2
7 Dirt Container Release Button 21 Handle/Extension Wand Release when using this cleaner on lino 8 On/Off Switch Button and hard flooring. Vax cannot be 9 Dirt Container 22 Upper Hose held responsible for damage to 10 Central Dust Chamber...
If the supply cord or plug is damaged, return the vacuum cleaner to a Vax IMPORTANT: If the inlet, hose or extension tube is Authorised Service Agent or suitably qualified blocked, switch off the vacuum cleaner and person for examination, repair or adjustment.
Slide handle through top of potentially cause some damage to the floor surface. back panel until it snaps NOTE: Vax recommends that you raise the height of into place. the brush bar when using this cleaner on lino and hard flooring.
Page 5
U90-MVX-P Mach VX Pet User Guide.qxd:v1 21/12/09 17:38 Page 5 All manuals and user guides at all-guides.com Vax Careline 0844 412 8455 Floor/Carpet Cleaning To change the dusting brush into an upholstery tool, simply snap off the square plastice ring housing the Move the handle and adjust it to the desired position for bristles.
U90-MVX-P Mach VX Pet User Guide.qxd:v1 21/12/09 17:38 Page 6 All manuals and user guides at all-guides.com vax.co.uk 5. Dirt container & filter: Remove foam filter Press tab on bottom of foam filter cover and pull to remove. removal & replacement WARNING: to reduce risk of injury from moving parts - unplug before servicing.
Page 7
U90-MVX-P Mach VX Pet User Guide.qxd:v1 21/12/09 17:38 Page 7 All manuals and user guides at all-guides.com Vax Careline 0844 412 8455 NOTE: The filter housing also needs to be washed Replace exhaust filter regularly with cold water and dried thoroughly before Return exhaust filter to base of cleaner and snap into replacing and restarting the vacuum cleaner.
Page 8
U90-MVX-P Mach VX Pet User Guide.qxd:v1 21/12/09 17:38 Page 8 All manuals and user guides at all-guides.com vax.co.uk 6. Belt or brushbar: removal To replace belt or brushbar Slide belt onto motorshaft. and replacement TOOL REQUIRED: Phillips screwdriver MOTOR SHAFT WARNING: to reduce the risk of injury from moving parts - unplug cleaner before changing belt or brush.
21/12/09 17:38 Page 9 All manuals and user guides at all-guides.com Vax Careline 0844 412 8455 Re-attach nozzle guard by aligning the four (4) tabs in the 7. Lightbulb: removal and base slots. Rotate nozzle guard back in place (Fig. 6/7).
U90-MVX-P Mach VX Pet User Guide.qxd:v1 21/12/09 17:38 Page 10 All manuals and user guides at all-guides.com vax.co.uk 8. General maintenance WARNING: To reduce the risk of injury from moving parts, unplug before servicing. WARNING: to reduce risk of injury from moving parts - unplug before servicing.
Monday-Friday 8.30am to 6.30pm. Saturday-Sunday 9.00am to 5.00pm. PROBLEM: Cleaner won’t run Any queries or concerns about using the Vax, call the Vax Cause: Not properly plugged into wall outlet. Careline. Please make a note of the serial number and Solution: Plug in firmly.
Page 12
All manuals and user guides at all-guides.com EEC STATEMENT OF COMPLIANCE Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the U90-MVX-P Mach VX Pet Upright is manufactured in compliance with the following Directives: Safety: 2006/95/EC Low Voltage Directive EMC: 2004/108/EC Electromagnetic Compatibility Directive Waste electrical products should not be disposed of with household waste.