Subscribe to Our Youtube Channel
Summary of Contents for Pro-Cut KMG-32
- Page 1 OWNER´S MANUAL MIXER GRINDER OPERATION INSTRUCTIONS MODEL KMG-32 READ THIS MANUAL BEFORE USING THE EQUIPMENT FOR THE FIRST TIME. 507134-A...
- Page 2 KMG-32 MIXER GRINDER INSTRUCTIONS FOR OPERATION, SERVICE AND MAINTENANCE OF THIS EQUIPMENT CONTENTS: PAGE INTRODUCTION UNPACKING III. INSTALLATION OPERATION KEY ELEMENTS IN MIXING/GRINDING QUALITY PRODUCT CLEANING VII. MAINTENANCE VIII. EQUIPMENT SPECIFICATIONS I.- INTRODUCTION: Congratulations you have acquired a Mixer Grinder, which is made of high quality long lasting materials that should give you years of trouble free operation and durable service.
- Page 3 KMG-32 MIXER GRINDER USAGE CAUTION AND RECOMENDATION FOR GRINDING: 1.- Utilize 3/8” plate or bigger for first grinding. IMPORTANT!: P o t e n t i a l d a m a g e t o e q u i p m e n t m a y o c c u r i f s m a l l e r p l a t e i s u t i l i ze d FIG.
- Page 4 KMG-32 MIXER GRINDER II.- UNPACKING: While unpacking the mixer-grinder take special care in removing the components and make sure that all are accounted for and check possible shipping damage: The grinding unit includes: Item Description item Description Headstock support Mixing blades...
- Page 5 KMG-32 MIXER GRINDER Reverse the steps and sequence to install the mixing blades and the grinding unit again (See Fig. 1): a) Insert Headstock (2) aligning hole and superior pin. Fix both parts with the Nut (3). b) Insert Worm (4) and Blade (5) – Blade´s sharp face must be forward.
- Page 6 KMG-32 MIXER GRINDER MIXING BLADES SPACER A special nylamid – Food contact approved engineering plastic - spacer (26) is added between the hopper fontal wall and mixing blades (8). This spacer eliminate the stress applied to Mixing blades shaft (9) and improve the operation by reducing the excessive movement and gap of mixing blades.
- Page 7 KMG-32 MIXER GRINDER The mixer-grinder is provided with a plug L19-30P type. To make a right connection, only it is necessary verify the appropriate size and the grounding type receptacle (See Fig. 5). Before completing the electrical connection, check the worm (4) and mixing blades (8) rotation. When grind button (GRIND) is pressed, the worm and mixing blades must rotate at the same time (the worm must rotates counter clockwise).
- Page 8 KMG-32 MIXER GRINDER CAUTION!: The equipment stays energized even though the selector is on “Stand by” option. Do not perform maintenance or any other service. Note: Footswitch interrupter only has Grind and Stop functions. While pushing paddle the Mixer-Grinder will grind and will stop immediately after release it.
- Page 9 KMG-32 MIXER GRINDER 2. Using a soft bristle brush (not provided), clean with adequate detergent each component, specially inside headstock (2) to eliminate waste and debris of food. 3. Wash every component with plenty of water. 4. Dry completely. Don't let soap cleaners dry on the surface. Rinse regularly to keep the chlorides found in most cleaners from affecting the natural luster of stainless.
- Page 10 KMG-32 MIXER GRINDER Note: When you clean the stainless steel parts, it is recommended to brush all components with a 1.5 inches head soft bristle brush (not provided). Make sure to clean all areas, specially the waving part inside the headstock support (1).
- Page 11 KMG-32 MIXER GRINDER 2. Replace the knife and plate when assembly becomes loose even though the Ring (7) is totally tight. 3. If the power cord (25) or the plug is damaged, they must be replaced by an authorized service technician or qualified personnel to avoid risk of electric shock.
- Page 12 KMG-32 MIXER GRINDER MEAT GRINDER DIAGRAM FOR COMPONENTS (SEE CENTRAL PAGES) ITEM DESCRIPTION HEADSTOCK SUPPORT HEADSTOCK WORM BLADE OR KNIFE PLATE RING MIXING BLADES MIXING BLADES SHAFT HEADSTOCK GASKET CABINET GASKET LATCH LATCH SCREW SPRING WIGNUT SCREW HOPPER GUARD GUIDE...
- Page 13 THANKS FOR READING THIS MANUAL. IF YOU HAVE ANY DOUBT REGARDING THE OPERATION OF THIS MEAT SAW, PLEASE CONTACT TO YOUR PRO CUT AUTHORIZED DEALER.
Need help?
Do you have a question about the KMG-32 and is the answer not in the manual?
Questions and answers