Advertisement
Available languages
Available languages
User Manual
With this unit you have decided on a highly precise and with many safety-relevant protective
devices that are used for carefree charging of your vehicle.
Important Note:
Please read these important safety instructions for charging your vehicle.
Keep this user manual. The charger has many safety functions. Please read these safety
information and warnings in this manual to be alerted of potential hazards.
Warning
Basic precautions must always be followed when using electrical products.
This manual contains important instructions, including the following, which are required and
must be followed during installation, operation and maintenance.
• Do not install or use the charger near ,explosive, caustic or flammable materials, chemicals
or vapours..
• Switch off the input power of the charger before installing or servicing the charger.
• The device is only designed for vehicles that are compatible with the IEC 62196 charging
standard.
• Do not use the charger if it is broken, cracked, frayed, broken or damaged
• Do not try to open, disassemble, repair, manipulate or modify the device
If you have any questions or repairs, please contact our customer service.
• Do not use the charger when you are in the vehicle or when exposed to heavy rain,
snow or severe weather.
• Be careful when transporting the charger.
• Do not touch the charging connector with sharp metal objects
• Do not pull the charging cable with force or with sharp objects
Warning
The device should be installed, adjusted and serviced by qualified electricians or
People who are familiar with the construction and operation of this type of EV-Charger
Failure to follow this precaution could result in death or serious injury.
• Incorrect installation and testing of the charger can lead to damage
No liability is assumed for the resulting damage.
• Make sure that the charging cable is well positioned during the charging process cannot be
walked on, damaged or burdened.
• Check the wire diameter according to the local electrical requirements
• Switch off the corresponding power supply before starting the installation.
Technical data:
• Operating voltage: 230V AC ±10%
• Operating current: 10 or 16 Amp adjustable
• Max. Output power: Typically 3,6 KW
• Housing: IP66, splash water protected
• Operating temperature: -25 bis + 55 °C.
• Display: color LCD, LED, stripes
• Protection against: over and under voltage, overload protection, short circuit protection,
over temperature protection, lightning protection, fault current. (RCD A).
• Dimensions: 249 x 104 x 48 mm
• Weight: 3 Kg
• Cable length: 5 meters
• Structure: CE standards EN62752:2016
• Art. Nr.: EM003ACC | BS-PCD030-5M
• Barcode: 4024559256028
Overview:
1. Grounding plug, suitable for 230V AC socket up to 16 A
2. Colour Display
3. Button to adjust the current
4. LED strip
5. EV charger plug
Display :
The high-resolution colour display of the EM2GO charging unit shows you the following
information:
1. Real-time charging current
2. Real-time voltage
3. Power consumption
4. Charging time
5. PCB temperature
6. Status display
Portable EV-Charger
EM003ACC
1
5
1
2
3
4
5
LED strip display
The LED strip signals the status of the charger:
1. LED shows nothing: Not in operation
2. LED is permanently lit green: Charger is connected.
3. LED green running: it is Charging
4. LED is permanently lit green: Charging process complete
5. LED flashing red: There is a defect.
1
2
NOTE: If the LED strip flashes red, the protection electronics of the EV charger was
addressed. In this case, please disconnect the mobile charger from the electric vehicle and
from the power grid. Submit the connections, cables and charger to a visual inspection.
If there are no visual defects, reconnect everything. If the red LED continues to flash, dis-
connect the charger from the electric vehicle and the mains supply and contact your specialist
consultant. Do not use the EV charger.
Charge vehicles:
1. First plug the grounding plug of the charger into a suitable socket. Press the button (3)
on the charger unit and switch charging current.
2. Remove the protective cap of the type 2 plug and connect it to the
Charging connection of the vehicle. Please note that the vehicle must be prepared and
adjusted for charging. The charging process begins.
3. When charging is complete, remove the grounding plug from the mains socket.
4. Remove the type 2 plug from the vehicle's charging socket.
5. Replace the protective cap on the type 2 plug.
NOTE: On some vehicle models the charging process does not start automatically.
In this case the switch on the charging unit (3) must be operated.
1
3
No liability for possible damage will be accepted in the event of incorrect operation.
If you need technical support, please contact our support team via our
website www.em2go.de.
Warranty and maintenance
2
• The warranty period for this charger is two years.
• The warranty expires if:
3
• No proof of purchase can be provided.
• The warranty period specified by the manufacturer is exceeded.
• The instructions for use, maintenance and storage are not followed.
4
• Damage or malfunction is caused by the ingress of foreign objects.
• In case of repair, disassembly or modifi cation by unauthorized persons.
• Damage caused by force majeure (such as lightning, overvoltage, earthquake, fire,
flood, etc.).
• Damage and malfunctions caused by other avoidable external factors.
• Damage and malfunction caused by improper use of the equipment, such as the ingress of
water or other liquids.
• Damage and malfunction caused by the mains power supply and a voltage not specified for
use with the charger.
We hereby declare, that this device carries the CE mark in accordance with the
regulations and standards. It conforms with the fundamental requirements of the of
(REDF) 2014/53/EU. EMC Directive 2014/30/EU, and the Low Voltage Directive
2014/35/EU. The full text of the EU declaration of conformity is available at the
following internet address:
Note on environmental protection:
After the implementation of the European Directive 2012/19/EU in the national legal
system, the following applies:
6
Electrical and electronic devices may not be disposed of with domestic waste.
Consumers are obliged by law to return electrical and electronic devices at the end
of their service lives to the public collecting points set up for this purpose or point of sale.
Details of this are defined by the national law of the respective country. This symbol on the
product, the instruction manual or the package indicates that a product is subject to these
regulations. By recycling, reusing the materials or other forms of utilising old devices, you are
making an important contribution to protecting our environment.
em2go
by D-Parts GmbH ● Birkenweiher Str. 16 ● 63505 Langenselbold, Germany V2_01_21
GB
3
4
5
2
4
5
www.d-parts.de/Konfo
Advertisement
