SATA 8T User Manual

Hydraulic crimper

Advertisement

液压电缆压接钳 8T
Hydraulic Crimper 8T
99018
使用说明书 \ User's Manual
中文
EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 8T and is the answer not in the manual?

Questions and answers

Summary of Contents for SATA 8T

  • Page 1 液压电缆压接钳 8T Hydraulic Crimper 8T 99018 使用说明书 \ User’s Manual 中文...
  • Page 2 中文 99018 产品描述 - 头部采用锻造合金钢材质,坚固耐用 - H 型工具头,钳头可旋转 180 度 - 快速压接设计,操作方便 - 使用六角型模具、压接紧密,不易脱落 - 旋转泄压阀即可完成复位 - 玻璃纤维绝缘手柄可耐电压,确保使用者的安全 性能参数 型号 99018 液压钳形式 整体式 出力 8 吨 行程 15.5mm 压接范围(mm ) 16~240 本体长度(mm) 模具形式 六角式 配置模具(mm ) 16,25,35,50,70,95,120,150,185,240...
  • Page 3 中文 99018 使用方法 活动手柄 钳头销 钳头 固定手柄 模具 回油开关 1. 拔出钳头销 - 检查被压接端子与电缆规格是否匹配。 - 选择与压接端子匹配压接模具。 - 更换压接钳模具,方法:如右图。 - 将连接端子放入工具头,顺时针旋紧回油开关,操作 活动手柄,压接开始。 - 则会有 [ 咯嚓 ] 声音,为安全保护装置打开;表示压接 操作完成。 - 逆时针旋松回油开关,活塞自动复位。 - 每次使用后,将工具清洁干净后放入存储箱。 2. 退出模具...
  • Page 4 中文 99018 操作注意事项 - 避免上下模具直接碰接,以免损坏压接头和上下模。 - 一年内不管是否有使用,都必须更换液压油,所更换液压油为 L-HV15 液压油。 - 操作时选择正确的压缩规格,以免造成挤压变形。 - 产品工作时,周边不得站人,严禁将钳头朝人工作,以确保安全。 故障检修 - 若长期未使用,出现油压不稳定,本产品可自动调整油压恢复正常。操作方法:将最小规格模具安装在产品上, 低速空压来回 5-6 次,油压自动调整。 - 若没有任何其他故障情况下,工具本身没有了压力,则处理方式为加满液压油。 - 当活塞发生后退之现象时,其原因为: 机体内部有杂物造成压接不紧,处理方式为内部处理干净。也可能阀门密封不良,油内混有空气,应排除空气。 - 活塞不能完全退回原位,是复位弹簧变形或损坏。...
  • Page 5: Product Description

    中文 99018 Product description - The head is made of forged alloy steel, strong and durable - H-type tool head, the tong head can be rotated 180 degrees - Quick crimping design, easy to operate - The hexagonal die is used, and the pressing is tight, so it is not easy to fall off - The reset can be completed by rotating the relief valve - Glass fiber insulated handle can withstand voltage to ensure the safety of users Performance parameters...
  • Page 6 中文 99018 Usage method Movable handle Tong head pin Nipper Fixed handle Mould Oil return switch 1. Pull out the tong head pin - Check whether the crimped terminal matches the cable specification - Select the crimping die matching with the crimping terminal. - Replace the die of crimping clamp.
  • Page 7: Operation Precautions

    中文 99018 Operation precautions - Avoid direct contact between the upper and lower dies, so as to avoid damaging the pressure joint and the upper and lower dies. - No matter whether it is used or not, the hydraulic oil must be replaced within one year. The hydraulic oil to be replaced is l-hv15 hydraulic oil.
  • Page 8 99018 版本号 / Version No: V_SC_99018_0702 世达工具(上海)有限公司 SATA TOOL (SHANGHAI) LIMITED 客户服务:上海市浦东新区碧波路 177 号 A 座 302 室 Customer service: Room 302, Area A, No. 177, Bibo Road, Pudong New Area, Shanghai 邮编 / Post: 201203 电话 / Tel.: (86 21) 6061 1919...

This manual is also suitable for:

99018

Table of Contents