Summary of Contents for IMST iOKE868 LoRaWAN
- Page 1 IMST GmbH Carl-Friedrich-Gauß-Str. 2-4, D-47475 Kamp-Lintfort iOKE868 LoRaWAN® User Manual Version 1.0 Document State initial Date October 2020 Document ID 4000/40140/160 © 2020 IMST GmbH - All rights reserved...
- Page 2 Date Comment October 2020 Initial Version Content General User Information Hardware Overview iO881A Startup Reader Functions Real Time Clock Synchronization LED and Push Button Usage Initial Setup Technical Characteristics iOKE868 LoRaWAN® / User Manual Version: 1.0 Page 2 of 12...
-
Page 3: General User Information
Terms and Conditions” of IMST GmbH, supplied at the time of order acknowledgment. IMST GmbH assumes no liability for the use of its products and does not grant any licenses for its patent rights or for any other of its intellectual property rights or third-party rights. - Page 4 The limitations on liability in favor of IMST GmbH shall also affect its employees, executive personnel and bodies in the same way. IMST GmbH is not responsible or liable for any such wrong statements.
-
Page 5: Hardware Overview
Hardware Overview This chapter provides an overview about the hardware of iOKE868. iOKE868 LoRaWAN consist of: iO881A for LoRaWAN antenna micro USB cable Figure: iO881A for LoRaWAN®, antenna and USB cable Features of iO881A USB-interface for generic power supply (power plug or battery pack) USB-interface for configuration and direct mode iOKE868 LoRaWAN®... - Page 6 Push button for status request and initial configuration. LED for signalling. Micro USB connector for configuration, optional direct mode and power supply. MMCX antenna connector for connecting the provided external antenna. iOKE868 LoRaWAN® / User Manual Version: 1.0 Page 6 of 12...
- Page 7 In this final step the calendar unit is updated to handle the configured events which control the subsequent application behavior. The following flow chart outlines the iO881A startup procedure and it's single steps. Figure : iO881A startup with invalid & valid configuration iOKE868 LoRaWAN® / User Manual Version: 1.0 Page 7 of 12...
- Page 8 The Continuous Capture Mode can be deactivated by a Stop command, or by activating the Single Capture Mode. Again the OBIS-ID Filter will be used to focus on the wanted specific data. iOKE868 LoRaWAN® / User Manual Version: 1.0...
- Page 9 Due to the fact that the clock crystal frequency can drift over temperature it is recommended to synchronize the RTC via ® LoRaWAN from time to time ( e.g. once per week ). iOKE868 LoRaWAN® / User Manual Version: 1.0 Page 9 of 12...
- Page 10 Red, continuously blinking LoRaWAN network time synchronization ® ® Green 2 x LoRaWAN network time synchronization successful Power saving in sleep mode Table : Firmware activities an LED signals iOKE868 LoRaWAN® / User Manual Version: 1.0 Page 10 of 12...
-
Page 11: Initial Setup
The iO881A requires an initial configuration before usage. This configuration can be done by means of a PC-Tool called WS-Configurator which is connected via serial interface (USB) to the device. For further information howto configure the iO881A please refer to the corresponding QuickStartGuide iOKE868 LoRaWAN® / User Manual Version: 1.0 Page 11 of 12... -
Page 12: Technical Characteristics
Typical +5°C to +55°C Mounting Via integrated magnet Housing Material: ABS, black Dimension: 47mm x 34mm x 22mm (without connectors) Certification RED (2014/53/EC) RoHS Directive (2011/65/EC) ® LoRaWAN 1.0.2 iOKE868 LoRaWAN® / User Manual Version: 1.0 Page 12 of 12...