Table of Contents
Advertisement
Quick Links
PLEASE NOTE: THE REMOTE CONTROL COMES PRE-PROGRAMMED TO THE FAN
REPROGRAMMING IS ONLY REQURED WHEN REPLACING THE REMOTE CONTROL
ATTENTION ELECTRICIANS:
ANY PROBLEMS FOUND DURING INSTALLATION OF THE FAN PLEASE CONTACT THE NATIONAL
WARRANTY NUMBER PRIOR TO LEAVING SITE. DO NOT REMOVE THE FAN FROM THE CEILING
UNLESS INSTRUCTED TO DO SO.
National Warranty Number | 1300 116 305
g
NOTE: THIS FAN MUST BE INSTALLED BY A LICENSED AND QUALIFIED
ELECTRICIAN IN ACCORDANCE WITH LOCAL AUTHORITY REGULATIONS
Storm 52
Installation & User Manual
Monday to Friday 9am to 5pm AEST
Australian Edition Version 2.1 April 2020
Advertisement
Table of Contents
Related Manuals for Aero Storm 52
Summary of Contents for Aero Storm 52
- Page 1 Storm 52 Installation & User Manual PLEASE NOTE: THE REMOTE CONTROL COMES PRE-PROGRAMMED TO THE FAN REPROGRAMMING IS ONLY REQURED WHEN REPLACING THE REMOTE CONTROL ATTENTION ELECTRICIANS: ANY PROBLEMS FOUND DURING INSTALLATION OF THE FAN PLEASE CONTACT THE NATIONAL WARRANTY NUMBER PRIOR TO LEAVING SITE. DO NOT REMOVE THE FAN FROM THE CEILING UNLESS INSTRUCTED TO DO SO.
- Page 2 IMPORTANT INFORMATION - PLEASE READ BEFORE ATTEMPTING INSTALLATION Please read these instructions carefully, be mindful of all warnings and safety information shown throughout this manual. Should you have any questions, please contact 1300 116 305. Please review the accompanying assembly diagrams before attempting installation. This fan MUST be installed by a licensed &...
-
Page 3: Table Of Contents
LOCATION AND INSTALLATION REQUIREMENTS Provide adequate clearance from the floor. The lowest point on the fan blades must be at least 2.1m (7 feet) from floor level in Australia Ceiling and at least 2.3m from floor level in the European Union and affiliated countries. -
Page 4: Fan Assembly & Parts List - Without Led Light Kit
FAN ASSEMBLY & PARTS LIST - WITHOUT LIGHT KIT Unpacking your Fan Unpack your fan and check the contents. Please check each item prior to installation, should you find any issues please contact the Warranty Helpline on 1300 116 305 for assistance. To reduce the chance of marks or possible damage please only remove the parts when required for installation. -
Page 5: Fan Assembly & Parts List - With Led Light Kit
FAN ASSEMBLY & PARTS LIST - WITH LED LIGHT KIT Unpacking your Fan Unpack your fan and check the contents. Please check each item prior to installation, should you find any issues please contact the Warranty Helpline on 1300 116 305 for assistance. To reduce the chance of marks or possible damage please only remove the parts when required for installation. -
Page 6: Installing Extension Rod (Optional Accessory)
INSTALLING EXTENSION ROD (OPTIONAL ACCESSORY) In accordance with Australian Standards, the fan blades must be at least 2.1 metres above floor level and the blades require at least 300mm clearance to the nearest object. DANGER! Before commencing installation, turn off electricity supply at the main power box or disconnect power by removing fuse or turning off circuit breaker. -
Page 7: Installing Hanger Bracket
INSTALLING EXTENSION ROD (OPTIONAL ACCESSORY) CONTINUED WITH LIGHT LOOM & FAN WITHOUT LIGHT LOOM & FAN (LOOM B) (LOOM A) INSTALLING HANGER BRACKET - ENSURE CAN TAKE 10KG LOAD National Warranty Hotline|1300 116 305 Monday to Friday 9am to 5pm AEST... -
Page 8: Installing Fan - Without Led Light
INSTALLING FAN - WITHOUT LIGHT In accordance with Australian Standards, the fan blades must be at least 2.1 metres above floor level and the blades require at least 300mm clearance to the nearest object. DANGER! Before commencing installation, turn off electricity supply at the main power box or disconnect power by removing fuse or turning off circuit breaker. - Page 9 INSTALLING FAN - WITHOUT LIGHT CONTINUED DANGER! Before commencing installation, turn off electricity supply at the main power box or disconnect power by removing fuse or turning off circuit breaker. This fan must be installed by a licensed and qualified electrician in accordance with local authority regulations. National Warranty Hotline|1300 116 305 Monday to Friday 9am to 5pm AEST...
-
Page 10: Installing Fan - With Led Light
INSTALLING FAN - WITH LIGHT In accordance with Australian Standards, the fan blades must be at least 2.1 metres above floor level and the blades require at least 300mm clearance to the nearest object. DANGER! Before commencing installation, turn off electricity supply at the main power box or disconnect power by removing fuse or turning off circuit breaker. - Page 11 INSTALLING FAN - WITH LIGHT CONTINUED National Warranty Hotline|1300 116 305 Monday to Friday 9am to 5pm AEST...
-
Page 12: Fan Remote Control Reprogramming
FAN REMOTE CONTROL PROGRAMMING - OPERATING THE FAN FROM THE REMOTE CONTROL NOTE: The Fan itself has NO DIP switches. Each individual fan must be set-up and programmed to the corresponding remote control where multiple fans are installed. If there is more than one fan please ensure the other fans remain powered off while programming. -
Page 13: Replacing Led Panel If Required
REPLACING THE LED LIGHT PANEL IF REQUIRED PLEASE NOTE: Should the light still not be functioning correctly once a new panel is installed a replacement reciver will also be required. please contact customer service on 1300 116 305 National Warranty Hotline|1300 116 305 Monday to Friday 9am to 5pm AEST... -
Page 14: Summer And Winter Mode Explained
SUMMER AND WINTER MODE EXPLAINED FORWARD (Summer) Mode Ceiling fans are an environmentally smart choice to assist with cooling and warming your home. In FORWARD (Summer) mode your ceiling fan will spin to push air down the centre of the fan producing a cooling breeze. -
Page 15: General Information
GENERAL INFORMATION 1. All electrical motors, including fan motors make some noise, and may feel hot to the touch. This is NOT a fault. 2. Ceiling fans tend to move during operation due to the fact that they are not rigidly mounted. (Rigid mountings can generate excessive vibration and stress on the mountings). -
Page 16: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSES PROBABLE SOLUTIONS Fan does not power Check the dwelling’s fuse/box circuit breakers has not No mains voltage going to fan. failed / tripped and check that 240V is available at the Terminal Block Isolation switch turned off. Check isolation switch is turned on. -
Page 17: Ceiling Fan Warranty Information
CEILING FAN WARRANTY INFORMATION This warranty applies only to Australian states and its mainland territories. The benefits of this warranty are in addition to any rights offered under state or territory law. Please also note the following, prior to requesting service, please consult the Troubleshooting section in the manual;... -
Page 18: Not Covered By Warranty
NOT COVERED BY WARRANTY. Any damage incurred after delivery to the owner that is not caused by a fault in the products materials or workmanship; damage from lightning or power surges; incorrect installation; damage due to incorrect installation; noise or other influence of ripple control or information access systems operated over power delivery infrastructure; water damage of any kind;... -
Page 19: Electrician Checklist
ELECTRICIAN CHECKLIST Electricians make sure everything on this checklist is ticked off before you leave the installation site. If you have trouble installing our product please refer to the trouble shooting section on page 11 first, then phone the AeroDC Warranty Hotline on 1300 116 305 (open 9am to 5pm EST). - Page 20 Distributed by EM Imports Pty Ltd 10 Overlord Place Acacia Ridge Queensland Australia 4110 Warranty & Support: AeroDC Ph: 1300 116 305 support@aerodc.com.au National Warranty Hotline|1300 116 305 Monday to Friday 9am to 5pm AEST NOTE: THIS FAN MUST BE INSTALLED BY A LICENSED AND QUALIFIED ELECTRICIAN IN ACCORDANCE WITH LOCAL AUTHORITY REGULATIONS...
Need help?
Do you have a question about the Storm 52 and is the answer not in the manual?
Questions and answers