Summary of Contents for Osaki EC2000
- Page 1 SERVICE AND REPAIR A comprehensive in house repair and service facility is available through your local agent. OTHER OSAKI PRODUCTS...
-
Page 2: Declaration Of Conformity
(fair wear and tear and/or misuse excepted). This does not affect your legal rights. Please retain supplier invoice as proof of purchase. AVAILABLE FROM YOUR DISTRIBUTOR Osaki continually strives to improve it products, specifications may change without prior notice. ©The Kennedy Group Ltd. 01/06... - Page 3 • 2,000 watt motor. • 40cm bar length. • 10m cable. • Anti-kick device. • “Quick stop” mechanism stops the chain in 0.15 seconds. • Automatic chain oiling system. • Safety guard. EC2000 ORDER CODE OSA-279-0260K OPERATORS MANUAL...
- Page 4 INTRODUCTION INTRODUCTION DESCRIPTION (See fig.4) When using the machine, always observe the enclosed 01 Rear grip safety instructions as well as the additional safety instructions. 02 Safety switch Denotes risk of personal injury or 03 Front grip damage to the tool. 04 Front finger guard / Chain break The safety instructions must be observed when using 05 Saw chain...
-
Page 5: Technical Drawings
TECHNICAL DRAWINGS THE NUMBERS MENTIONED INTHETEXT CORRESPOND WITHTHE PICTURES... - Page 6 TECHNICAL DRAWINGS THE NUMBERS MENTIONED INTHETEXT CORRESPOND WITHTHE PICTURES...
-
Page 7: Safety Instructions
SAFETY SAFETY INSTRUCTIONS • The chainsaw must not be operated by children and young people. The only exception to this prohibition are young persons of 16 years and over Safety instructions and accident prevention. To prevent the incorrect handling of the chainsaw, who can use the chainsaw under supervision as part of their training. - Page 8 SAFETY • Never use the chainsaw if it has a defective • Branch lopping work should be carried out by trained ON/OFF-switch. personnel! Risk of injury! • Use the cable only for its proper purpose. Never • Pay special attention to branches under tension. Do carry your electric tool by its cable.
- Page 9 fig.2,C) the upper chain tensioning borehole (E) and sion again (See fig.3) Do not tension the chain too the oil duct , or contact your local Osaki agent (Be sure tightly. When cold, it should be possible to lift the chain in the middle of the guide bar approx.
-
Page 10: Chain Brake
(See fig.2 C), the upper chain tensioning borehole (E) and the oil duct, or contact Use the saw only with approved extension cables with your lokal Osaki agent. Check the oil level every 15 the prescribed insulation and connections designed minutes during the operation. - Page 11 TECHNICAL DRAWINGS THE NUMBERS MENTIONED INTHETEXT CORRESPOND WITHTHE PICTURES...
- Page 12 TECHNICAL DRAWINGS THE NUMBERS MENTIONED INTHETEXT CORRESPOND WITHTHE PICTURES...
- Page 13 KICK-BACK TIPS ON CHAINSAW USE • After switching on, the chainsaw will run immediately at high speed.To switch off: SAWING UP WOOD (See fig.7A,7B) Release either the ON/OFF switch (14) on the rear grip or the other switch (2) on the front grip. To saw up wood, please observe the safety regulations The release of the ON/OFF will result in the chainsaw and proceed as follows:...
- Page 14 KICK-BACK THE NUMBERS MENTIONED INTHETEXT CORRESPOND WITHTHE PICTURES...
-
Page 15: Maintenance
The chainsaw must be running before is comes the Osaki repair and service facility. In the event of any inquiries and spare parts orders, always quote the type, into contact with the wood. -
Page 16: Troubleshooting
LIKELY CAUSE SOLUTION No electricity. Check socket, cable and plug. A damaged switch has to be replaced by the Osaki repair and service facility. Motor does not run. See section “Chain brake” and Chain brake. “Releasing the chain brake” . - Page 17 KEY TO SYMBOLS USED 1 Warning! 2 Unplug immediately if the power cord or plug becomes damaged! 3 Protect from the damp. 4 Read the operation manual and follow the warnings and safety instructions! 5 Wear protective helmet, goggles and earmuffs! 6 Always pull the plug out of the power socket before doing any work on the chainsaw...
- Page 18 EC2000...
Need help?
Do you have a question about the EC2000 and is the answer not in the manual?
Questions and answers