Jebao AL Series User Manual

Aquarium light

Hide thumbs

Table of Contents

Quick Links

Download this manual

Caution:

Do not look directly to the LEDS when you plug in the power or the light

is on due to high power and brightness of the LEDs.

Please use in ventilated environment. Do not use in narrow environment.

Please make sure the fan function work normally when the light is in use.

Clean the fan and light body routinely with brush or air blower.

Time program stops if you manually set the light.

Only the owner's account can control the light. You can log in to your

account in different devices to control the light.

Products and APP are subject to change along with the technical improvements.

Please refer to the actual product and APP.

Aquarium Light

AL、AK Series

User's Manual

Table of Contents

Summary of Contents for Jebao AL Series

Page 1 Aquarium Light AL、AK Series User’s Manual Caution: Do not look directly to the LEDS when you plug in the power or the light is on due to high power and brightness of the LEDs. Please use in ventilated environment. Do not use in narrow environment. Please make sure the fan function work normally when the light is in use.
Page 2: Product Introduction
1. Product Introduction AL、AK series Aquarium Light can perfectly imitate the natural light under the sea. It creates a natural living environment for fish, corals and other marine creatures in your tank. AL、AK series Aquarium Light is composited of 6 sets of LEDS, including white (cold white and warm white), royal blue, blue, violet (violet and ultra violet).
Page 3 AL-120 LEDs White Blue 1 Blue 2 Violet Green Total Watt AL-150 LEDs White Blue 1 Blue 2 Violet Green Total Watt AL-200 LEDs White Blue 1 Blue 2 Violet Green Total Watt Note: The above watt is the sum of power consumption of LEDs, control panel, fan and power adaptor.
Page 4 3. LED Diagram AK-70 AL-120...
Page 5 AK-80, AL-90, AL-150, AL-200 4. LED Spectrum Diagram...
Page 6: Product Installation
5. Product Installation 5.1. AL-90，AL120，AL-150，AL-200 Light Screw Bracket Screw Bracket Part 2 Light body Mounting Base Bracket Part 1 Bracket Screw Clamping Screw Installation Steps： Connect the Bracket Part 1 and the Mounting Base with the Bracket Screw. Fix the Mounting base to the tank with Clamping Screw. Connect Bracket Part 1 and Bracket Part 2 with the Bracket Screw.
Page 7 5.2 AK-70, AK-80 Bracket Screw Light Screw Bracket Part 2 Light body Bracket Part 1 Mounting Base Bracket Screw Clamping Screw Installation Steps： 1) Connect the Bracket Part 1 and the Mounting Base with the Bracket Screw. 2) Fix the Mounting base to the tank with Clamping Screw. 3) Connect Bracket Part 1 and Bracket Part 2 with the Bracket Screw.
Page 8 AK Series: Wi-Fi Indication Light is located in the lower front part of the light seen as a white spot. On/Off Button is located on the opposite side of the Wi-Fi indication light on the upper part of the light as seen as a transparent button. AL Series: AL90 AL120, AL150, AL200 6.1 Explanation of Wi-Fi Indication Light...
Page 9 6.2 Instruction Press ON/OFF Button to turn on or off the light, or adjust brightness manually. The brightness changes from 0%-10%-25%-50%-80%-100% each time. Press Wi-Fi button for about 5 seconds and the Wi-Fi indication light starts flashing alternately in green and red. The light is into smart configuration mode.
Page 10 The APP, named “Jebao Aqua”, is available in App Store for IOS system users and Google Play for Android system users to download. The User can search Jebao Aqua in either App Store or Google Play to download the application. Alternately user may scan the barcode on the package or user’s manual to download the...
Page 11 Android System 1, Application market download People can download the “ Jebao Aqua” APP in Google play and PP Assistant 2, Scan the below barcode and download the APP PS: APP may have difference from the instruction due to the upgrade.
Page 12: Login Page
7.2 User registration, login and password reset 7.2.1 Account registration Login Page ①Open Jebao Aqua App and tap Create new account. ②Fill in the information as required and tap Create account； ③After registration, return to the login page and enter the account and password to log in.
Page 13: App Instructions
Tap Forget Password on the login page. Enter your email address and tap Send link. Check your email and follow the instructions to reset your password. 7.3 APP Instructions 7.3.1. Main page...
Page 14 Add new devices. Add new devices. Go to My Groups. Go to Settings. 7.3.2 Add new light...
Page 15 Tap My Devices. Tap Add Now or + sign on the upper right-hand side to add your devices, tap Aqua lights (local). Configuration mode: Make sure your phone is connected to 2.4G band Wi-Fi before configuration. There are two types of configuration modes, Smart configuration and AP configuration...
Page 16 ① modes. Choose one mode to link your device. Smart Configuration ： Press Wi-Fi button for about 5 seconds and the Wi-Fi indication light starts blinking alternately in green and red. The Device is in smart configuration mode. Check Device is in smart configuration mode and tap Next to start smart configuration.
Page 17 Follow the instructions. Enter Wi-Fi password and tap Next. Make sure your device, phone, and router are as close as possible during the configuration progress. The page will display all the devices. Choose the device you want to add and tap on the device name, then tap Add.
Page 18 ② AP distribution network Tap Start to start using your device. ： Press Wi-Fi button for about 10 seconds and green and red light starts blinking simultaneously. The Device is in AP configuration mode. Tap AP Network in the upper right corner of add device page to enter into AP configuration.
Page 19 Check Device is in AP configuration mode and tap Next. Enter the Wi-Fi password and tap Next.
Page 20 Note: Due to different operating systems, IOS and Android will operate differently in the following details. A. IOS: After entering the Wi-Fi password, you need to manually switch the Wi-Fi of the phone to "Jebao_WiFi-xxxx", the specific operation is as follows. Tap Go to settings.
Page 21 Tap “Settings” in the upper left corner to enter the mobile phone settings page. Go to Settings > Wi-Fi and connect to “Jebao_WiFi-xxxx” with password 123456789.
Page 22 123456789 After successful connection, tap Jebao Aqua on the upper left corner to return to the APP. The configuration starts automatically. Tap Start to control the device after the device has been added successfully. ：After input the Wi-Fi password, tap Next and...
Page 23 choose the device to start configuration. If the device cannot be found, go to Settings>Wireless & networks > WLAN to turn off and on the WLAN switch. The device can then be displayed. Tap Start to control the device after the device has been added successfully.
Page 24 Power button ： To turn on / off the light Daylight mode Night mode Current mode Manual mode Sunset mode Sunrise mode Automatic mode Morning mode Note: Press the icon for 2 seconds to enter the selected mode setting page.
Page 25: Manual Control Mode
Manual Control Mode Press or drag the bar to change the brightness of LED. ① Manual control: Drag the bar to left or right till it reaches your desired brightness. (Note: White LED group contains both cold white and warm white LEDs.
Page 26 Sunrise Mode Daylight Mode (Note: There might be network delay. Try it again till it gets effective) - Daylight Mode: It’s effective between 10:00 and 17:00 for manual ④ control. It has White and Blue LEDs with lesser red, green and violet LEDs adjustable at 10% brightness minimum.
Page 27 Sunset Mode Evening Mode (Note: There might be network delay. Try it again till it gets effective) ⑦ Automatic Mode Quick Setup: Tap the clock icon to the automatic mode. Tap“Load Preset”. There are several default modes to choose , include LPS 1、LPS 2、 LPS/SPS 1、...
Page 28 Normal Setup: You can set your own program. By selecting the color of the LED to adjust the corresponding brightness at the corresponding time, finally click "save" and "run". Choose LED color Load the preset program Save the program Set the brightness Run the program...
Page 29 7.3.4 My Groups 1) Add a group Tap My Groups Choose My Groups, Select “ADD NOW” or choose “+” icon on the upper right- handside to add a group.
Page 30: Manage Groups
Tap “Aqua Lights(Local)”, after enter the group name, select the lights that need to be grouped, and tap "add". Click to enter the group, enter the group control page, the operation and single light control operation is the same. 2）Manage groups Tap to go to the edit page You may rename the group or re-select the lights which you want to add or delete from the group.
Page 31 Tap to edit Rename Select light Add light Tap Save Tap “-” on the individual light you want to delete and tap Delete to delete the light.
Page 32: Delete Groups
3） Delete Groups Tap to edit Choose Delete Group. Tap Confirm to delete the group. 7.3.5 Rename and Delete a light User can rename the light for convenient device management. You can also delete the light from your app. IF you want to add the light back, you need to reconnect it to your Wi-Fi network.
Page 33: Error Report
保存 7.3.6 Error Report If the light is overheated, will warn the overheated error. Check if the fan is blocked or broken. If the light doesn’t connected to the Wi-Fi network, it reports connection error. 8. Others 1) When the light is connected to power, the light will flash once. Please avoid looking directly to the light.
Page 34 APP will only be saved the data, but not display by the light. 4) The light has the thermostat. When the light temperature reaches 75℃, the thermostat cut off automatically to disconnect the power to ensure safety. Jebao Co., Ltd. Add：Tongmao Industrial Park, Dongsheng, Zhongshan, Guangdong, China Tel：+86-760-28136708, 28136720 E-mail：info@jebao.com...

This manual is also suitable for:

Ak series