12 Notes.................. 19 The SCHUSTER Transferpressen GmbH takes no responsibility for damages arising from misuse, repairs, and modifications which where carried out by third, not authorized parties, as well as for damages arising from non observance of the instruction manual. This handbook was constructed with great care, a liability for small negligent mistakes, for example printing error, however are excluded.
OVERVIEW HEAT PRESS Front view: Instruments box no 1 Hand protection Base plate Intermediate Main Switch frame Side covering Heat platen with Textile catcher Teflon sheet with handles Instruments box no 2 Back View: Compressed-air connection & compressed-air filter min. 8 bar / 116 psi Electric connection: GT-1011: 400 V / 12 A...
SAFETY INSTRUCTIONS Read through the following advice before taking the heat Important safety regulations • All operations on the heat press can only be press into service. It is necessary to consider all warnings accomplished by specialized staff who gained an This heat press presents dangers if used inappropriately, or and advice indicated on the heat press.
UNPACKING & CHECKING SHIPMENT Heavy Heavy * Only TWIN-Version - 6 -...
Page 6
UNPACKING & CHECKING SHIPMENT Cut open the transport straps for the base plate SHIPMENT (pos 2) and the textile catcher (5). ATTENTION: Parts may tilt and they are Pos. Quantity Item Solo | Twin heavy! 1 | 1 Heat press Lean both part carefully against a wall.
Page 8
HEAT PRESS ALIGNMENT AND FRONT PLATE MOUNTING Adjustment is effected by the four stands A to a the casing by moving it onto the bushing and Now first tighten the screws on the lower side and height between 90 and 96 cm / 35,4 and 37,8 inch. simultaneously turning the nut clockwise.
BACKPLATE MOUNTING (only TWIN-version) M6x12 + instruments washer (M6x12+washer). Connect the plug with the casing by pushing it onto the bushing and by turning the nut clockwise. Roll the 2nd trolley into the guide rails until you can see nothing but the front pair of rolls.
MOUNTING TEXTILE CATCHER BASE PLATE MOUNTING / (Only TWIN-version) HEIGHT ADJUSTMENT The intermediate frames serve to adapt the space between work and heat platen according to the thickness of the material to be printed. (See section „6.1 Base plate height adjustment“) The following description shows the assembly.
START OPERATION | SETTINGS INSTRUMENTS BOX NO 1 Temperature control (pos 3): Measured temperature LED „Heating“ Set temperature SET-button Increasing Decreasing INSTRUMENTS BOX NO 2 temperature temperature (Only TWIN-Version) Time control (pos 4): Countdown Set time Key operated switch f. operation mode (see chap 6.5): START-button (Press simultaneously to start printing operation) 0 –...
START OPERATION | SETTINGS 5.1 Electric connection 5.3 Switching the heat press on and off Setting of operating pressure herewith explicitly point that Turn the main switch to „ON“. Now the heat press is in a The operating pressure is controlled by the pressure considerable (mortal!) dangers for people and stand-by mode.
SETTINGS | PRINTING OPERATION 6.4 Time setting Go back to manual or automatic mode for current PRINTING OPERATION activities when you have finished maintenance / setting The remaining printing time is indicated in the upper line Switch the heat press on and proceed with the settings. works.
CHANGING TEFLON FOIL M5-screw Heavy Heavy Spring Handle Side covering Spring holder M8-screw Disconnect heat press from electricity! Disconnect heat press from electricity! First of all disconnect the press from Push a base plate into the heat press. Pull the electricity! handle upwards in a diagonal direction, then move it downwards and place the whole Teflon...
MAINTENANCE • Check regularly if water has accumulated in • Should you notice that the hand protection the compressed air filters. If there is water in cannot be moved unobjectionably the springs the glass drain it by turning the black valve need greasing.
Hand protection does not Check if both hand protections have reached FON: +49-7732-30279-10 close completely dead stop by lightly pushing with your hand. If not see 4.3 FAX: +49-7732-30279-13 Pressure set too low Increase pressure (see chap. 6.2) E-MAIL: kontakt@schuster-transferpressen.de - 17 -...
Need help?
Do you have a question about the GT-1011-SOLO and is the answer not in the manual?
Questions and answers