Summary of Contents for Feel Good mr.steam iTEMPO
- Page 1 Installation, Operation & Maintenance Manual ™ ™ i T E M P O & i T E M P O / P L U S C O N T R O L S mr steam ® Feel Good Inc. www.mrsteam.com...
-
Page 2: Table Of Contents
Table of Contents: General Information s you follow these instructions, you will notice warning and caution General Information.........1 symbols. This blocked information is Before Installing ..........1-2 important for the safe and efficient installation and operation of this Dimensional Information........3 control. These are types of potential hazards that may occur during Installations ...........4-7 installation and operation:... - Page 3 mr steam ® Installation & Operating Instructions _____________________________________________________________ BEFORE INST LLING peel and stick warning W RNING Carefully inspect the control and packaging sticker is provided in the MrSteam steam for shipping damage. In the event of ship- generator Installation, Operation and Main- ping damage, please contact the carrier for tenance Manual.
-
Page 4: Before Installing
If an iTempo or iTempo/Plus control is Wizard or iGenie controls with anything other installed outside the steam room a Remote than a Mr.Steam iTempo compatible steam Temperature Probe (PN MSTS) must be in- generator. Mr.Steam residential steam genera-... -
Page 5: Dimensional Information
mr steam ® Installation & Operating Instructions ______________________________________________________________ 2 ” Dimensional Information for the Round and Square iTempo and iTempo/Plus ™ ™ 1” BOX CONTENTS: ” • iTempo ™ or iTempo/Plus ™ Control ” • Control Cable (30 ft.) • Steam head 5”... - Page 6 mr steam ® Installation & Operating Instructions ______________________________________________________________ 5 ⁄8” Installation Instructions for Round & Square iTempo and iTempo/Plus ™ ™ STEP 1 Determine the desired installation location of the control. The iTempo and iTempo/Plus controls are designed to ™ ™...
- Page 7 mr steam ® Installation & Operating Instructions ______________________________________________________________ STEP 2 Diagram 1 5 ⁄8 7 ⁄8 Make a 2- ” wide by 3- ” high cutout in the desired control location. Do not oversize or undersize the cutout. STEP 3 Diagram 2 Route the control cable (provided with the control) from the wall cutout to the steam generator.
- Page 8 mr steam ® Installation & Operating Instructions ______________________________________________________________ DI GR M 4 C UTION If the generator is on for more than a few minutes steam will start coming out of the steamhead. Insure that steamroom is not occupied. STEP 5 Diagram 4 Remove and discard peel-off paper to expose adhesive liner.
- Page 9 mr steam ® Installation & Operating Instructions ______________________________________________________________ IMPORT NT NOTE: o not apply excessive amounts of silicone. o not apply silicone to any other parts of the control including the adhesive gasket. STEP 7 Diagram 6 Insure the mounting surface is clean and dry as required for good adhesion.
-
Page 10: Installing The Remote Temperature Probe
mr steam ® Installation & Operating Instructions ______________________________________________________________ c. in a location representative of the desired Installing the Remote steam bathing temperature. Locating the MSTS Temperature Probe (PN: MSTS) near the steamhead or near direct steam emis- The Remote Temperature Probe is required sions may result in poor steamroom temperature when the iTempo or Tempo/Plus Controls control. - Page 11 mr steam ® Installation & Operating Instructions ______________________________________________________________ Temperature Probe Connection Knock-Out Temperature Probe Cable Temperature (30 feet) Sensor Probe Mr.Steam Steam Generator (shown with cover removed and NOT installed) DI GR M 1 rawings for Illustrative Purposes Only.
- Page 12 mr steam ® Installation & Operating Instructions ______________________________________________________________ S T E M R O O M I N T E R I O R 5. Route the end of the probe cable with the tem- perature probe through the wall into the steam DI GR M 2 room as shown in Diagram 2.
-
Page 13: Itempo Operating Instruction
mr steam ® Installation & Operating Instructions ______________________________________________________________ iTempo Operating Instructions ™ The iTempo Control features programmable digital temperature control, a fixed (60) minute duration, ON/OFF and P USE. The control can be set at a temperature range from 80˚ up to 120˚... - Page 14 mr steam ® Installation & Operating Instructions ______________________________________________________________ TIMER FE TURE When the control is turned ON a 60 minute time du- ration is initiated. The control will turn off after 60 minutes unless the control is turned off manually. MEMORY FE TURE If the control is turned off manually before 60 minutes then the default temperature of 110˚F will be used...
-
Page 15: Itempo/Plus Operating Instruction
mr steam ® Installation & Operating Instructions ______________________________________________________________ iTempo/Plus ™ Operating Instructions The iTempo/Plus Control features programmable tempera- ture control, programmable time duration, clock, roma- Steam, ChromaSteam , ON/OFF and two personal settings. ® mr.steam Set the steambathing temperature according W RNING to personal preference, however it is highly recommended temp... - Page 16 mr steam ® Installation & Operating Instructions ______________________________________________________________ iTempo/Plus ™ Operating Instructions (cont.) SETTING THE CLOCK Diagram 3 DI GR M 3 mr.steam When the display is not flashing: Press and hold the TIME key until the display starts flashing. temp Use the UP/DOWN keys to select the desired time, at this time the M/PM logo will be displayed.
- Page 17 mr steam ® Installation & Operating Instructions ______________________________________________________________ SETTING THE TEMPER TURE Diagram 6: Press TEMP key to set the desired temperature or dis- play the temperature setting. mr.steam Diagram 7: The control is preset and will display a temperature setting of 110˚F (default setting).
- Page 18 mr steam ® Installation & Operating Instructions ______________________________________________________________ CH NGING THE TEMPER TURE UNITS (˚F/˚C) When the generator is Off, Press and hold aroma ON/OFF key for 10 seconds. The temperature units will be displayed as Fahrenheit (TuF) or mr.steam Celsius (TuC).
-
Page 19: Warranty
mr steam ® Installation & Operating Instructions ______________________________________________________________ Display mr.steam Up Key Time Display/ Time Display/ temp time Adjust Key Adjust Key Down Key ON/OFF Key Program Key aroma chroma AromaSteam ChromaSteam Care Tips for all Controls and Steamheads 1. Use only mild soap and water on a soft cloth to clean the control and steamhead. 2. - Page 20 TEMPL TE FOR CONTROL INST LL TION SEE PG mr steam ® 5 ⁄8” Feel Good Inc. Products, information and specifications are subject to change without notice. For more information call Sales & Support at: 7 ⁄8” 1.800.76.STE M (East Coast) 1.800.72.STE M...