Advertisement
Quick Links
Cozy Cottage Kennel
Tools Needed:
-Cordless Drill (12V or higher)
-#2 square drive bit
-Hammer
-6' Step ladder
-Tape Measure
-Square utility knife w/ blade & hook blade
®
Little Cottage Co.
PO Box 455
Berlin, OH 44610
330-893-4212
www.cottagekits.com
© 2007-2008 Little Cottage Co.
Advertisement
Summary of Contents for Little Cottage Cozy Cottage Kennel
- Page 1 -Cordless Drill (12V or higher) -#2 square drive bit -Hammer -6’ Step ladder -Tape Measure -Square utility knife w/ blade & hook blade ® Little Cottage Co. PO Box 455 Berlin, OH 44610 330-893-4212 www.cottagekits.com © 2007-2008 Little Cottage Co.
- Page 2 1 in the middle as shown. your Cozy Cottage Kennel. Refer to your buy list for specific contents, which will vary by unit. Fasten treated 2x4 rim with 2 1/2” screw into Install treated 2x4 as shown.
- Page 3 1/2” screws every 8”. Locate the first wall panel and set in place. Continue installing walls. Make sure the wall is flush with the edge of the floor and fasten with 2 1/2” screws. Construction Manual © 2007-2008 Little Cottage Co. Page 2...
- Page 4 Fasten panels on bottom with 1 1/4” black head Install duratemp strip and fasten with 1 1/4” screws every 8 to 10 inches. screws. Use angle to make sure it is flush with the floor. Construction Manual © 2007-2008 Little Cottage Co. Page 3...
- Page 5 Measure 2 1/2” from the outside of the post to This is what it should look like when the top the top plate as shown and fasten with 2 1/2” plates are done. screws. Construction Manual © 2007-2008 Little Cottage Co. Page 4...
- Page 6 Next set the gable in place on the top of the wall. gable are flush and fasten with 2 1/2” screws. Next set the gable on the other end of the wall. Continue with gable installation. Construction Manual © 2007-2008 Little Cottage Co. Page 5...
- Page 7 Install the 2x3 on the bottom of the gable end Install the gable as shown and fasten with 2 1/2” and fasten with 2 1/2” screws to strengthen the screws. gable. Construction Manual © 2007-2008 Little Cottage Co. Page 6...
- Page 8 Install 2x3’s for door braces and fasten with 2 Install the 2x3 on the top of the door opening 1/2” screws. to strengthen the gable and fasten with 2 1/2” scews. Construction Manual © 2007-2008 Little Cottage Co. Page 7...
- Page 9 Next install K-panel as shown. Use the angle and make sure the K-panel is flush on the inside of the 2x6 and fasten with 2 1/2” screws. Construction Manual © 2007-2008 Little Cottage Co. Page 8...
- Page 10 Make sure you have 20” from the siding to the 1/4” scews. 4x4 and fasten with 2 1/2” screws. Install the door stop and fasten with 1 1/4” Install the child door trim. Fasten with 2 1/2” screws. screws. Construction Manual © 2007-2008 Little Cottage Co. Page 9...
- Page 11 Install the aluminum corner trim and fasten with small white nails. Next install the chain link panel from the inside Fasten with 1=screw with washer on all corners out as shown. as shown. Construction Manual © 2007-2008 Little Cottage Co. Page 10...
- Page 12 Install inside chain link panel. Measure 26 1/2” against siding to the outside panel. Next install the top panel as shown and fasten Attach panels with clips as shown. with screw and washer into 2x2. Construction Manual © 2007-2008 Little Cottage Co. Page 11...
- Page 13 Install bottom door first and center door. Fasten Install door spacer bar for adult door installation. with 2 1/2” black headed screws. Continue to install top half. Locate adult door latch. Construction Manual © 2007-2008 Little Cottage Co. Page 12...
- Page 14 Install as shown. Fasten with screws as shown. Install strike plate as shown. Locate roof rafters. Use wooden gussets to tie rafters together and Continue from picture #94. fasten with 1 1/4” screws. Construction Manual © 2007-2008 Little Cottage Co. Page 13...
- Page 15 Measure 3” from the edge of the 2x6 to the edge Truss layout. of the rafter and fasten with 2 1/2: screw. This is for the dormer to set on. Install heart window as shown. Heart window and wood parts. Construction Manual © 2007-2008 Little Cottage Co. Page 14...
- Page 16 Install T-bar as shown. 1/4” screws. Fasten T-bar with 2 1/2” screw. Top plates are marked off where trusses need to be placed. Fasten dormer with 2 1/2” screws. Install dormer as shown. Construction Manual © 2007-2008 Little Cottage Co. Page 15...
- Page 17 Fasten with 2 1/2” screws. Install sheeting as shown. Fasten bottom corner with 1 1/4” screw. Install 2’ OSB and fasten bottom corner with 1 fasten opposite bottom corner with 1 1/4” screw. 1/4” screws. Construction Manual © 2007-2008 Little Cottage Co. Page 16...
- Page 18 Continue installing sheeting with 2 1/2” screws. lay dormer OSB from the top to the bottom and mark off with the pencil. Install valley plate along the pencil mark as Next install the dormer OSB sheeting. shown. Construction Manual © 2007-2008 Little Cottage Co. Page 17...