Contents Niche Zero Manual Contents Important Safeguards Electrical safety Trouble shooting First use of Niche Zero Using the Niche Zero 9-10 11-14 Care and Cleaning 15-16 Guarantee...
Niche Zero is malfunctions or has been plugged in again. damaged in any manner; it 7. Do not place the Niche Zero must be replaced or repaired on or near a hot gas or electric by the manufacturer, its...
Page 4
8. Any significant spillage 12. Avoid contact with onto the surface under or moving parts. around the Niche Zero, or 13. The Niche Zero Grinder can onto the Niche Zero itself, be used by adult persons should be cleaned and with reduced physical,...
Page 5
Important Safeguards 17. The Niche Zero is not intended over the edge of a table, to be operated by means of counter, touch hot surfaces or an external timer or separate become knotted. remote control system. 22. The Niche Zero is designed 18.
If a longer extension cord is used: The marked electrical rating of the extension cord should be at least as great as the electrical rating of the Niche Zero. The extension cord should be a grounding-type cord. The cord should be arranged so it will not drape over the countertop or table top where it can be pulled on by children or tripped over.
Check to see if the Niche Zero is plugged into a grounded outlet and the lid is closed. If it is, unplug the Niche Zero, then plug it back in again. If the Niche Zero still does not work, check the plug fuse or circuit breaker on the electrical circuit the Niche Zero is connected to and make sure the circuit is closed.
First Use of Niche Zero WARNING: do not use when set to calibrated as you will damage the burrs. There may be coffee residue in your grinder. If there is, this is from testing to make sure your grinder performs to its best.
Using the Niche Zero Before use remove all packaging. Plug into outlet, the red LED will glow to show there is power to the Niche Zero. Your Niche Zero has been factory calibrated and adjusted to setting 20. 1. Open lid and rotate the bean 2.
Page 10
4. Replace grind cup on 7. For espresso, fit portafilter tray underneath. over grind cup. 8. Invert grind cup and 5. Close lid (Niche Zero will portafilter, shake and tap not operate if the lid is grind cup, then remove. open) and flick power switch up, to switch on.
Niche Zero. If it does not align, then only move black bezel so the white dot is in line with the calibrate mark, the Niche Zero is now recalibrated.
Page 12
Use a dampened soft microfibre cloth to clean the sweep arms and chamber floor. Clean the adjustment threads with a dry toothbrush and very lightly lubricate with food safe silicone grease. After deep cleaning, run 18g of coffee beans through the Niche Zero and discard.
Page 13
WARNING: always make sure grinder is off and unplugged when cleaning. Cleaning the motor housing, bean funnel and wooden parts • Do not immerse the motor housing or any part of the Niche Zero in water. • Never immerse the burrs or burr-shaft assembly in water.
Page 14
Additional Information First use after cleaning: The first time(s) you grind coffee some will remain in the Niche Zero and you may notice a slight increase in grind retention for the first few uses. Seasoning burrs: Grind quality is good from the start but will be at its peak consistency once the burrs have ground around 10kg.
This warranty period is not extended as a result of purchasing any additional products from NICHE. The original purchaser/ Indiegogo backer must notify NICHE in writing within eight (8) days if there are defective parts. Written notice in all events must be received by NICHE before expiration of the warranty period.
Page 16
Such excluded damages include, but are not limited to, loss of profits, loss of revenue, loss of data, loss of use of the NICHE product or any associated equipment, cost of capital, cost of substitute or replacement equipment, facilities or services, down time, original purchaser's time, the claims of third parties, including customers, and injury to property.
Need help?
Do you have a question about the Zero and is the answer not in the manual?
Questions and answers