1. Manuals
  2. Brands
  3. Murphy WallBed Systems Manuals
  4. Indoor Furnishing
  5. SBF
  6. Assembly instructions manual

Murphy WallBed Systems SBF Assembly Instructions Manual

Panel bed frame kit
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Panel Bed
Frame Kit
ASSEMBLY
INSTRUCTIONS
(SBF & SBLM)
TWIN/TWIN XL| FULL | QUEEN | KING
86 6 . 8 44. 9255 / / MU RP HYBE D DE POT.COM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SBF and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Murphy WallBed Systems SBF

Summary of Contents for Murphy WallBed Systems SBF

  • Page 1 Panel Bed Frame Kit ASSEMBLY INSTRUCTIONS (SBF & SBLM) TWIN/TWIN XL| FULL | QUEEN | KING 86 6 . 8 44. 9255 / / MU RP HYBE D DE POT.COM...

  • Page 2: Carton Contents

    Note: Each Frame Carton contains one Single, Double, Queen or King Steel Bed Frame complete with leg assembly and necessary hardware. Mechanism components are in separate carton. ✓ QTY. FRAME CARTON ITEMS COMMENTS (SBF) Frame End Sections Identical Head & Foot Frame End Sections Identical Right or Left 3(5)
  • Page 3 PROJECT SECTIONS Gather Tools & Hardware Obtain Wood & Cut Parts Using The Cabinet Cut list Mount The Lift Mechanisms To The Side Panels Install The Springs On The Lift Mechanisms Assemble The Bed Cabinet Attach Bed Cabinet Securely To Wall Assemble Steel Bed Frame &...

  • Page 4: Section 1: Gather Tools And Hardware

    Select Handles from your local decorative hardware supplier to pull the bed open. Have them on-site at the time of assembly. Handles are not provided in in the Panel Bed Frame Kit. Check to be sure that you have the SBF and SBLM Cartons, and the Lumber Components and Hardware before starting assembly.

  • Page 5: Section 2: Cabinet Cut List

    SECTION 2: CABINET CUT LIST (VERTICAL ORIENTATION) Visit MURPHYBEDDEPOT.COM/CUTLIST for a material cut list diagram. Cut and finish all pieces before assembly MATTRESS SIZE: 39” X 75”(XL 80”) (990mm X 1905mm (XL 2032mm)) // 11” (280mm) MAX THICKNESS OUTSIDE CABINET DIMENTIONS: 44 1/2”W X 83 1/4” (XL 88 1/4”)H X 16”D TWIN BED/TWIN XL (1130mm X 2115mm (XL 2242MM) X 406mm) PROTRUSION FROM WALL: 85”...
  • Page 6 SECTION 2: CABINET CUT LIST (VERTICAL CONTINUED) MATTRESS SIZE: 76” X 80” (1930mm X 2032mm) / / 11” (280mm) MAX THICKNESS OUTSIDE CABINET DIMENTIONS: 81 1/2”W X 88 1/4”H X 16”D KING BED (2070mm X 2242mm X 406mm) PROTRUSION FROM WALL: 90” (2286mm) CABINET MATERIAL: Four sheets of 3/4”...
  • Page 7 SECTION 2: CABINET CUT LIST (HORIZONTAL CONTINUED) MATTRESS SIZE: 54” X 75” (1372mm X 1905mm) / / 11” (280mm) MAX THICKNESS OUTSIDE CABINET DIMENTIONS: 80”W X 64 3/4”H X 16”D DOUBLE/FULL BED (2032mm X 1645mm X 406mm) PROTRUSION FROM WALL: 64” (1626mm) CABINET MATERIAL: Four sheets of 3/4”...

  • Page 8: Section 3: Mount The Lift Mechanisms To The Side Panels

    SECTION 3: MOUNT THE LIFT MECHANISMS TO THE SIDE PANELS Notes: 1. This step remains the same for vertical or horizontal versions. 2. The numbers in parenthesis () are in millimeters 1. Exactly mark the mounting holes on the inside of each panel, according to Drawing 1. 2.

  • Page 9: Section 4: Install The Springs On The Lift Mechanisms

    SECTION 4: INSTALL THE SPRINGS ON THE LIFT MECHANISMS SPRING APPLICATION CHART Notes: 1. Please note these are recommendations only. The actual number of springs required will depend on the total weight of the bed-face unit including the mattress and all bedding. 2.

  • Page 10: Section 5: Assemble The Bed Cabinet

    SECTION 5: ASSEMBLE THE BED CABINET (VERTICAL ORIENTATION) Assembly may be most easily accomplished by laying one Side Panel (#2) flat on a padded surface and attaching the top assembly (#3&4), Head Board (#3), Bottom Rear Base (#5), and Bottom Kick (#6).
  • Page 11 SECTION 5: CONTINUED (VERTICAL ORIENTATION) Top Panel Headboard Bottom Rear Base DRAWING 4.
  • Page 12 SECTION 5: ASSEMBLE THE BED CABINET (HORIZONTAL ORIENTATION) If possible, the bed cabinet should be assembled in the room where it will be used. Be sure the Lift Mechanisms are securely installed. Note: 1. If the room is carpeted you may raise the Bottom Kick up 1/4” (7mm) to clear the carpet. More than 1/4”...
  • Page 13 SECTION 5: CONTINUED (HORIZONTAL ORIENTATION) 1”x1”x1 3/4” (25x25x44) Angle Brackets Note: Upper Brackets clear Wall 3.0” (76) 20.0” (508) DRAWING 6.

  • Page 14: Section 6: Attach Bed Cabinet Securely To Wall

    SECTION 6: ATTACH BED CABINET SECURELY TO WALL You may or may not wish to remove the baseboard to allow the bed cabinet to fit flush against the wall. if you do remove the baseboard, save for later trim and replacement. If you do not wish to remove the baseboard, you may use a shim or filler strip of the same thickness at the top, between the cabinet and the wall.

  • Page 15: Section 7: Assemble Steel Bed Frame & Face Panels

    SECTION 7: ASSEMBLE STEEL BED FRAME & FACE PANELS Note: It is very important to have the bed frame centered, left to right, on the Bed Face Panels. Any error will be noticed in the vertical sightline when the bed is closed. 1.
  • Page 16 SECTION 7: CONTINUED Wall/Cabinet - Vertical (twin through queen) Frame flush with end of face panels Head of bed Stiffener Stiffener Stiffener 1.0” (.25) Foot of bed 1.0” (.25) Leg Stop Bed Face Panel Bed Face Panels Side View (do not install legs at this time, it is shown for reference only!) DRAWING 8.
  • Page 17 SECTION 7: CONTINUED Stiffener Placement - King Beds Only Head of bed Stiffener Stiffener Stiffener 2 Stiffeners 3.25” (83) Foot of bed DRAWING 9. Use 5 Stiffeners total: 3 equally spaced head to foot 2 against inside of rail (foot end) to provide added strength...
  • Page 18 SECTION 7: CONTINUED Wall/Cabinet - Horizontal (all sizes) Frame flush with end of face panels Head of bed Wood Stiffener Stiffener Stiffener Stiffener 1.0” (.25) Foot of bed 1.0” (.25) Leg Stop Bed Face Bed Face Panel Panels Side View (do not install legs at this time, it is shown for reference only!) DRAWING 10.

  • Page 19: Section 8: Set The Lift Mechanism

    SECTION 8: SET THE LIFT MECHANISM DRAWING 11. Holding one foot against the bottom front edge of the Side Panel and using the supplied steel tube, level the Tension Arm out until you can set the Arm Lock to the flanged standoff at hole A (see drawing 13).

  • Page 20: Section 9: Install The Bed Face Panel Unit

    SECTION 9: INSTALL THE BED FACE PANEL UNIT 1. Insert round head allen bolt (Hardware Card #2) from the outside of the frame through Hole #1 on each side of the Steel Bed Frame, approximately 6 3/4” from head of frame. Use Nylock nuts to securely tighten.

  • Page 21: Section 10: Install Handles - Legs - Mechanism Covers - Mattress

    SECTION 10: INSTALL HANDLES - LEGS - MECHANISM COVERS - MATTRESS 1. Position and secure handles for ease of operation. Recommended placement on vertical beds: approximately 16” (406mm) from the Panel top to the top of the handles. Be sure to avoid stiffeners. 2.
  • Page 22 SECTION 10: CONTINUED 6. Slide the powder coated steel mechanism covers in place - secure with #8x1 1/4” (M4x32mm) black wood screws (Hardware Card #2) through the standoff on the backer plate. Insert tabs on steel mechanism cover into slots on the backer plate. Align top hole on steel mechanism cover with the standoff on the backerplate and secure with DRAWING 16.

  • Page 23: Section 11: Enjoy Your New Finished Panel Bed

    SECTION 11: ENJOY YOUR NEW FINISHED PANEL BED! Note: Bed linens may be stored on the mattress, but do not store pillows on the bed or inside the cabinet. Damage may occur if doing so. DRAWING 17. DRAWING 18. (Vertical Bed Cross Section)

This manual is also suitable for:

Sblm

Table of Contents