Advertisement
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
9
warranty.
Wear appropriate protective clothing. When handling lubricants refer to manufacturer's instructions and conform to local regulations.
9
Use the gun in a suitable working area. Keep area clean and tidy and free from unrelated materials and ensure there is adequate
9
lighting.
Maintain correct balance and footing whilst performing the task. Ensure floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
Dispose of waste grease in accordance with local authority regulations.
9
When not in use ensure the battery is removed.
9
DO NOT allow unauthorised persons to operate the gun.
8
WARNING! DO NOT tamper with or open pump unit. Doing so will invalidate your warranty.
‰
DO NOT point grease gun at yourself or other persons or animals.
8
DO NOT pull the grease gun unit by the hose.
8
DO NOT use the gun for a task it is not designed to perform.
8
DO NOT operate the gun when you are tired or under the influence of alcohol, drugs or
8
intoxicating medication.
When not in use, clean the unit and store in a dry, safe, childproof area.
9
2. INTRODUCTION
High power, professional, cordless grease gun. Ideal for in-field lubrication where power and
Speed are required. Suitable for 400g cartridges, manual or bulk filling. Features LCD battery
condition indicator, air bleed and heavy-duty aluminium pressure head. Supplied with battery and
mains charger in storage case.
3. SPECIFICATION
MODEL NO: ...................................................... CPG12V.V4
Battery: ...........................................................12V 2Ah Li-ion
Flow Rate: ................................................................. 80g/min
Hose Length:.............................................................. 680mm
Pressure: ...................................................................6000psi
Replacement Parts: ...............................................................
CPG12VBP ...........................................Replacement Battery
CPG12V.V2-ICA ...................................In-Car Power Adaptor
4. OPERATION
IMPORTANT WARRANTY INFORMATION: the battery pack fitted to this cordless tool are
considered to be a consumable item and its ability to accept charge will reduce over time. We
will provide warranty against mechanical and electrical defect for a period of one year - this does
not cover fair wear and tear. If the battery is not properly charged before 1st use, or regularly
conditioned, its capacity will diminish. Under these circumstances we will not replace the battery
pack even if it is less than one year old.
4.1.
CHARGING THE BATTERY
IMPORTANT: Before using the grease gun for the first time the battery must be charged
for a minimum 1.5 hours.
4.1.1.
To charge the battery, slot the battery onto the charger (Fig 1.1).
DO NOT obstruct the vents situated on the top and bottom of the charger as this will
8
cause the charger to overheat.
4.1.2.
Once plugged in correctly and the mains has been switched on, the red light situated at
the front of the charger (Fig 1.2) will illuminate. When charging is complete the green light
will illuminate.
4.2.
REMOVING THE BATTERY PACK
4.2.1.
To remove the battery from the unit press the two buttons located each side of the battery
simultaneously and pull the battery away from the body.
4.2.2.
To insert the battery, line up the ridges on the battery with the slots on the handle base
and push towards the unit firmly until you hear a click.
4.2.3.
Gun may be operated from a 12V vehicle battery by using the in-car adapter, fitted to gun
in place of battery pack.
4.3.
CARTRIDGE LOADING
4.3.1.
Unscrew the grease tube from the grease gun.
4.3.2.
Fully draw back the plunger handle.
4.3.3.
Insert the open end of the cartridge into the grease tube and push it all the way in (Fig
2). Remove the seal or pull tab end from the cartridge.
4.3.4.
Screw the grease tube back into the grease gun. Press the catch plate and release the
plunger rod. Push down on the plunger handle.
4.4.
SUCTION FILLING
4.4.1.
Unscrew the grease tube from the grease gun.
4.4.2.
Ensure the handle has been released (by pressing the catch plate).
4.4.3.
Submerge the open end of the grease tube into grease bucket by approximately 50mm
(2") and slowly pull the plunger handle out fully (Fig 3).
4.4.4.
Screw the grease tube back in to the grease gun. Press the catch plate and release the
plunger rod. Push down on the plunger handle.
© Jack Sealey Limited
Original Language Version
fig.1
fig.2
fig.3
CPG12V.V4 Issue 1 07/08/2020
Advertisement
