Related Manuals for LoadSurfer WH20L-65
Summary of Contents for LoadSurfer WH20L-65
- Page 1 Operate manual & Parts manual Hand Pallet Truck with BF Integrated Pump WH20L-65 WH25L-65 PWH25-II PWH30-II PWH35-II (85mm standard & 75mm profile) Note: Owner and operator MUST read and understand this operating instructions before use this pallet truck.
-
Page 2: General Specifications
All of the information reported herein is based on data available at the time of printing. The factory reserves the right to modify its own products at any time without notice or incurring in any sanction. Please verify with the factory for possible updates. 1. GENERAL SPECIFICATIONS WH20L-65 PWH25-II PWH30-II PWH35-II WH25L-65 Model No. - Page 3 . Draw-bar 2. Pin 3. Axle with hole 4. Elastic pin 5. Fork frame (Fig. 1) When attaching the handle, you had better squat just behind the pallet truck. Then you: 2.1. Insert the draw-bar onto the pump piston (A), then use a hammer to insert the axle with hole (K) into the hydraulic pump and draw-bar from the right to left.
-
Page 4: Maintenance
3. TO ADJUST RELEASE DEVICE On the draw-bar of this pallet truck, you can find the control handle which can be regulated in three positions : Raise - handle down Drive position - handle in center position Lower - handle up, the lever moves back the drive position when released. If however they have been changed, you can adjust according to following step: 3.1 If the forks elevate while pumping in the DRIVE position, turn the adjusting nut on the adjusting bolt or adjusting screw clockwise until pumping action does not raise the forks and the DRIVE... -
Page 5: Troubles Shooting
4.4 LUBRICATION Use motor oil or grease to lubricate all moveable parts. 6. GUIDE TO SAFETY OPERATION For safe operation of the Hand Pallet Truck, please read all warning signs and instructions here and on the pallet truck prior to use. 6.1 Do not operate the pallet truck unless you are familiar with it and have been trained or authorized to do so. - Page 6 - The impurities in the oil cause the release valve to be unable to close - Replace with new oil. tight. fork - Inspect and replace the waste descends - Some parts of hydraulic system is parts. without cracked or bored. - Banish the air.
- Page 7 General parts for PWH25-II/PWH30-II/PWH35-II Part No. Description Part No. Description 17010101 Handle assembly 17010116 PU Steering wheel Ø180*50 17010102 Chasis (540*1150) (2.5T/3T) 17010117 Nylon Steering wheel Ø180*50 17010102-1 Chasis (685*1220) (2.5T/3T) 17010116-1 PU Steering wheel Ø200*50 17010102-2 Chasis (540*1150) (3.5T) 17010117-1 Nylon Steering wheel Ø200*50 17010102-3 Chasis (685*1220) (3.5T) 17010116-2 Rubber Steering wheel Ø180*50...
- Page 8 General parts for WH20L-65/WH25L-65 with 65mm profile & PWH25-II-75 with 75mm profile New P/N Description New P/N Description 17010101 Handle assembly 17010124 Axle 16×40 17010102 Chasis (540*1150) (75 low profile) 17010143 Locknut M6 17010102-1 Chasis (685*1220) (75 low profile) 17010126 Rod end...
- Page 9 Pump & handle parts details PWH25-II PWH30-II Part No. Description Item Parts No. Parts details 17010201 Small pump core 17010316 Draw-bar 17010202 Cover of spring 17010327 Torsional Spring 17010205 Big spring 17010310 Blade Spring 17010332 Pump seals kit Ø31.5 for 2.5T/3T 17010311 Spring Pin 4x30 17010360 Small cylinder 17010314 Spring Pin 6x30...
- Page 10 Pump & handle parts details for PWH35-II Item Parts No. Parts details Qty. Item Parts No. Parts details Qty. 17010201 Small pump core 17010316 Draw-bar 17010202 Cover of spring 17010327 Torsional Spring 17010205 Big spring 17010310 Blade Spring 17010332-1 Pump seals kit Ø35 for 3.5T 17010311 Spring Pin 4x30 17010360...
- Page 11 Pump & handle parts details WH20L-65/WH25L-65 & PWH25-II-75 with 75mm profile New P/N Description QTY Item Parts No. Parts details Qty. 17010201 Small pump core 17010316 Draw-bar 17010202 Cover of spring 17010327 Torsional Spring 17010205 Big spring 17010310 Blade Spring...