Advertisement
Quick Links
Y
a
l
e
P
r
o
f
e
s
s
i
o
Y
a
l
e
P
r
o
f
e
s
s
i
2
1
LED
When the battery voltage is low, the LED will flash every 30 sec.
While the smoke Detector is transmitting the signal, the LED will flash.
While the batteries are inserted and the Smoke Detector is in warming and calibration process, the
LED will flash for 8~22 min.
Test Button
2
The Test Button is pressed in the following situations:
Learning – In the Smoke Detector.
To test the radio communication range.
To test if the Smoke Detector is functioning normally.
To silence the alarm
3
Battery compartment
4
Mounting Hole
Mounting Bracket
5
Hook
6
B
a
t
t
e
r
y
B
a
t
t
e
r
y
3 "AA" Alkaline batteries are used to supply power.
When the Smoke Detector has low battery, a low battery signal will be transmitted along with regular signal
transmissions. If the battery voltage is low, the LED will flash accompanied with a Low-volume beep once
every 30 sec and inform the Control Panel regularly. Low Battery warning typically starts 1 month before
complete exhaustion.
<
N
O
T
E
>
<
N
O
T
E
>
When changing batteries, after removing the old batteries, press the Test button twice to fully discharge
before inserting new batteries.
I
n
s
t
a
l
l
a
t
i
o
n
P
I
n
s
t
a
l
l
a
t
i
o
n
P
Step 1.
Insert the 3 "AA" batteries into the battery compartment taking care that the connection respects correct
polarity showing on the battery holder.
Step 2.
While the 3 batteries are inserted, the Smoke Detector will sound 2 short beeps, LED start flashing and
begin the 6-minute warming period.
Step 3.
During the 6-minute warming period, you can learn the Smoke Detector into the Panel.
To do the learning process：
a). Put the Control Panel into "Add Device" Mode (or "learning" mode) to learn the ID code of the Smoke
Detector. (Please refer to operation manual of the panel.)
b). Press the Test Button on the Smoke Detector, the LED will be on for 2 sec and the buzzer will sound a
2-tone beep to indicate it's functioning normally with successfully radio transmitting.
n
a
l
W
i
r
e
l
e
s
s
o
n
a
l
W
i
r
e
l
e
s
s
1
3
r
o
c
e
d
u
r
e
s
r
o
c
e
d
u
r
e
s
S
m
o
k
e
D
e
t
e
c
t
S
m
o
k
e
D
e
t
e
c
4
o
r
(
2
2
1
4
6
)
t
o
r
(
2
2
1
4
6
)
5
6
Advertisement
Summary of Contents for Yale 22146
- Page 1 When the battery voltage is low, the LED will flash every 30 sec. While the smoke Detector is transmitting the signal, the LED will flash. While the batteries are inserted and the Smoke Detector is in warming and calibration process, the LED will flash for 8~22 min.
- Page 2 c). If the Control Panel successfully receives the signal, the panel will respond accordingly to indicate the completion of the learning-in process. Please refer to the manual of the panel. Step.4 When the 6-minute warming period is over, one short beep will sound to indicate that the Smoke Detector is starting calibration process.
- Page 3 As the operation condition of the smoke detector may vary after being installed for some time, you may wish to recalibrate the smoke detector to take a new smoke detection threshold value and ensure optimal performance of the smoke detector. To do this, ...